Built to transform steam into liquid during the boil, Spike Brewing's steam condenser lid will enable you to brew inside without worrying about moisture collecting on your walls and ceiling, which can cause mold issues. These lids are not only designed to fit Spike kettles, but will also work with most other kettle brands on the market. From a better boil-off rate to major cost savings and conveniences, you will find many benefits by adding this to your brew setup. Features & Specs: Compared to boiling without a lid, the Steam Condenser Lid has a 50% reduced boil-off rate and results in a ~6% total boil-off. Replaces the need to install a hood for indoor brewing Prevents mold from forming on walls and ceiling Third-party lab tested to show that DMS is completely undetectable (under 25 ppb) after only 30-45 minutes of boiling Discharge water is very hot and can be used for cleaning Compatible with Spike Kettles and the Spike Solo 1.5" tri-clamp port for CIP ball 4" tri-clamp port for hop additions Water usage: 15 gallons/hour for 10g, 15g & 20g lids 25 gallons/hour for 30g &. 50g lids Lid, pump, condenser mister, piping, clamps, gaskets, barbs & caps included with purchase For more information, see Spike Brewing's FAQ. To get started using the lid, see our Steam Condenser Lid Product and Process guides. Note: Limited inventory availability in-store. Sizes not carried in-store will be drop shipped from the vendor.
$360.00 - $475.00
Spike Brewing's special 5/8" pickup tube flows up to 4x better than their competitors 1/2" size. These 5/8" tubes work perfectly with their full port valves which have a 5/8" flow diameter; no flow restriction. Spike Brewing's proprietary fittings uses quick connect technology. The quick connect fitting simply hand screws into the kettle and the pickup tube easily pushes in/pulls out; no tools needed. Features: One size fits all kettles Large 5/8" diameter 304 stainless tube Simply push in for seal; no tools required Proprietary stainless push to connect fitting included Sized to pick up from the bottom edge of the kettle Made in the USA
$30.00
10 GALLON STAINLESS BREW KETTLE - V4 Spike Brewing has once again re-designed their brew kettle. They make one of the best brewing kettles available on the market. It is the thickest kettle on the market, with US welded fittings (no more weldless fittings) at a factory direct price. Kettle Features: 2.5 - 6 gallon batch size 304 (18/8) stainless steel Sanitary welded coupler design (done at our facility in Milwaukee, WI) 1.2mm thick walls (thickest on the market) 5mm tri-clad bottom (induction capable) Internal volume markings Polished finish 13.8¨ wide by 17.0¨ tall Domed bottom design Bottom coupler 1.5" off the bottom (1 gallon mark) Top coupler 6" off the bottom (4 gallon mark) Lid is included Pictured Ball Valve and Thermometer Sold Separately. Limited availability in store. Drop ships from vendor.
$285.00
FLEX FERMENTER Introducing the new Spike FLEX! The FLEX was designed to be the most versatile, upgradable and longest lasting small batch fermenter on the market. With currently over 20 accessories (and counting) you'll never run out of fun toys to bling your FLEX out with. You can use the FLEX as a simple bucket fermenter with an airlock or add some accessories to get you all the way up to a 15 psi capable brite tank and anywhere in between!All hardware shown HERE is included! Flex Features: 304 stainless steel; 1.2mm (18ga) All sanitary welded ports (no-weldless fittings) Designed for 2.5 to 6 gallon batches 7 gallon total capacity 2 psi working pressure Strong seal to keep oxygen and bacteria out Use for pressure transfers to your keg or bottling bucket Etched volume markings Fully polished finish Dimensions: 15" wide by 21¨ tall (to top of airlock) See additional dimensions here Lid Features: 4" TC modular top port Allows for hop additions, temp control coil, top sight glass, etc Airlock port Body Features: 1.5" TC racking port with rotatable racking arm 1.5" TC secondary port for thermometer, sample valve, etc Limited availability in store. Drop ships from vendor.
$290.00
The Spike Brewing casters screw directly into the bottom of their conical legs for easy installation. The CF5, 10 and 15 use a 3" caster while the CF30 uses a larger 4" caster. CF5, CF10, CF15 Specifications: 3" caster wheel Set of 3 Non-marking wheel Locking brake + locking swivel CF30 Specifications: 4" caster wheel Set of 4 Non-marking wheel Locking brake + locking swivel *Spike Brewing recommends a standard or extended bracing shelf when using the casters for added stability* Caster wheel install and instructions:Install + instructions
$40.00 - $63.00
Specifically designed for our Tank Bottom Drain Boil and Solo kettles, this racking arm is the key component to make sure you take only the highest quality wort to your fermenter and leave hops and trub behind in your kettle. The dual 1.5" TC flange allows the pickup tube to attach to the kettle and allows for a 1.5" TC accessory to attach to the arm as well. We use 5/8" tubing which flows up to four times better than our competitors 1/2" size. Tank Racking Arm fits all 5 sizes of the Tank Bottom Drain Kettles Oversized 5/8" diameter 304 stainless tube Indicator pin lets the brewer see which way the tube is pointing when installed and covered in wort Rotatable when installed from the outside Made in the USA **A 1.5" gasket and clamp will need to be purchased separately if you do not already have spares**
$45.00
These Spike Brewing Spike+ false bottom is for use with their Spike+ line which uses TC fittings. For the standard Spike kettle line that uses NPT fittings please see HERE. Design Features: All stainless design; no Silicone gasket to make a seal Low profile design; extremely low dead space (<.25gal) Best filtering on the market due to dual stage filter design; 99.9% grain filtering efficiency TC Pickup tube, gasket and clamp are included False bottom and pick up tube are Made in the USA! 2 Stage Filtering: Stage 1: Filters through top plate's optimally engineered sized laser cut slits Stage 2: Bottom ring supports the grain weight while also filtering the wort again before it reaches the pickup tube **False bottoms are not designed to filter pellet hops in the boil kettle. Instead you'll want to create a whirlpool to center the hop material and then drain using a side pickup (HERE)**
$135.00 - $250.00
The Spike Brewing insulated FLEX jacket uses high quality, extra thick, yet flexible neoprene material to insulate your FLEX from the worst ambient conditions like a hot garage or cold basement. Each custom designed, hand stitched (in the USA) jacket is custom tailored to fit the FLEX. This jacket was designed by a former Lululemon designer because if you're going to cover up shiny stainless steel it better look amazing. We think she did the trick! Specifications: Sewn in the USA (of imported fabric from Japan and China) Reinforced stitching around all ports, legs and handles for extra strength Helps maintain stable fermentation temps regardless of ambient conditions Stops the tank from ‘sweating’ in warm weather Interior Velcro for attaching the optional heater Machine washable Detailed TC-100 product guide:Product Guide.pdf
$95.00
Cap any 4” port with this stainless steel cap. Specifications: 4" TC 304SS
$16.00
CF5 SPIKE CONICAL UNITANK Spike Brewing has completely re-designed their stainless conical line from the ground up. It took a year in the making and are confident that these are the best conical fermenters on the market! Along with the new TC100 Temp Control System, you'll have everything you need to Elevate Your Brew Day! CF5 Features: 304 stainless steel; 1.2mm (18ga) All sanitary welded ports (no-weldless fittings) All hardware shown here is included! Designed for 2.5 to 6 gallon batches 7 gallon total capacity 15 psi working pressure (always use a 15 psi pressure relief valve) Use for pressure transfers Use as a brite tank Etched volume markings 14" wide by 29¨ tall Fully polished finish Lid Features: 4" TC modular top port Allows for hop additions, temp control coil, top sight glass, etc Three 1.5" TC ports which allow for: Blow Off Port – Dedicated port for an airlock or blow off tubeHop Port – Dedicated port for adding hopsPRV Port – Dedicated port for your pressure relief valve (PRV) Stainless band clamp for attaching the lid Completely removable lid for easy cleaning Body Features: Huge 2" TC bottom dump with butterfly valves (no more stuck yeast dumps) 1.5" TC racking port with butterfly valve 1.5" TC sample valve (for taking gravity readings) 1.5" TC thermowell with 3" dial thermometer Limited availability in store. Drop ships from vendor.
$726.00
Spike Brewing conicals come equipped with this 100% sanitary sample valve. Taking samples has never been so easy; simply twist the valve handle to slowly draw out a sample from your fermenter for a gravity reading. The one downside is you might end up with lower final volumes due to how easy it is to take taste tests ;)Specifications: 1.5" TC 304SS FDA Silicone seals 3/8” barb
$35.00
Spike Brewing's TC100 temp control system will manage both cooling and heating of your Spike Conical. The digital controller's temp probe will feed into the included thermowell on our CF Series Conical. Also included is a specially fitted neoprene jacket which features reinforced port holes to reduce the chance of ripping during install. Last (and maybe the coolest item) is Spike Brewing's special insulated tubing. This almost eliminates tube cooling losses and will prevent your cooling lines from sweating all over your floor! Cooling:When the temp in the conical rises above the set point it will turn on the pump submerged in your cold water reservoir (bucket of ice water, dorm fridge, aquarium or glycol chiller, DIY AC chiller, etc). This will pump cold water/glycol through the temp control coil, which mounts to the lid, cooling your beer until it reaches the controller set point. Heating:When the temp in the conical falls below the controller set point the optional heater will kick on warming the unit up. Detailed product guide:Product Guide.pdf TC100 Package:-Digital closed loop controller (heating and cooling)-Insulated tubing (more efficient and no more sweaty tubes!-Temp control coil-Neoprene insulated jacket-Submersible pump (pumping cold water through the temp coil)-Temp Coil Quick Connect Fittings TC100 + Heat Package:-TC100 Package (above)-Optional heater (for us northern brewers) Limited availability in store. Drop ships from vendor.
$325.00 - $550.00
Set of 3 replacement o-rings for the Spike Brewing 5/8" quick connect pickup tube fittings. Specifications: FDA approved Buna-N Sold in set of 3
$2.50
The straight quick connect fittings allow you to increase the length of the Spike Brewing insulated tubing. This insulated glycol tubing is sold in increments of 6ft. If you need to increase the length of tubing, this is your solution. Specifications: 1/2" to 1/2" connections 2 fittings included per purchase (enough to connect 2 lengths of the Spike Brewing insulated tubing)
$11.00
Spike Brewing's TC-100 temp control system will manage both cooling and heating of your FLEX. The digital controller's temp probe inserts into the included thermowell that attaches to the secondary port of the FLEX. Also included is a specially fitted neoprene jacket which features reinforced port holes to reduce the chance of ripping during install. Lastly, (and maybe the coolest item) is Spike Brewing's special insulated tubing. This greatly reduces tube cooling losses and will prevent your cooling lines from sweating all over your floor during the dog days of Summer! Cooling:When the temp in the FLEX rises above the set point of the controller, it will turn on the pump submerged in your cold water reservoir (bucket of ice water, aquarium, glycol chiller, DIY AC chiller, etc). This will pump cold water/glycol through the temp control coil, which mounts to the lid, cooling your beer until it reaches the controller set point. Heating:When the temp in the FLEX falls below the controller set point the optional heater will kick on warming the unit up to the desired temp. Detailed product guide:Product Guide.pdf TC-100 Package:-Digital temp controller (manages heating and cooling)-Insulated tubing-Temp control coil-Thermowell-Neoprene Insulated Jacket-Submersible pump-Temp Coil Quick Connect Fittings TC-100 + Heat Package:-TC-100 Package (above)-Optional heater (for us northern brewers) Limited availability in store. Drop ships from vendor.
$325.00 - $395.00
50 GALLON SPIKE+ BREW KETTLE Introducing Spike Brewing's new Spike+ line of kettles! Spike+ is just that, an improvement on an already great platform. The Spike+ line draws from the pro side of brewing with the standard use of tri-clamp (TC) fittings. TC fittings do not have any threads and use a gasket and clamp which allows for quick attaching/detaching of fittings. The Spike+ line is for the most serious homebrewers! While designing the setup of the kettle, Spike Brewing offset the ports on these kettles, so you have ample room to use our butterfly valves, or other accessories, with ease. Kettle Features: 15 – 32 gallon batch 304 (18/8) stainless steel Sanitary welded coupler design (done at Spike Brewing's facility in Milwaukee, WI) 1.5mm thick walls (thickest on the market) 6mm tri-clad bottom (induction capable) Internal volume markings Polished finish 23.6¨ wide by 27.1¨ tall Domed bottom design Bottom coupler 2" off the bottom (4 gallon mark) Top coupler 4" off the bottom (8 gallon mark) Staggered design keeps the top port submerged with half batches Lid is included Pictured Ball Valve and Thermometer Sold Separately. Limited availability in store. Drop ships from vendor.
$775.50
10 GALLON SPIKE+ BREW KETTLE Introducing Spike Brewing's new Spike+ line of kettles! Spike+ is just that, an improvement on an already great platform. The Spike+ line draws from the pro side of brewing with the standard use of tri-clamp (TC) fittings. TC fittings do not have any threads and use a gasket and clamp which allows for quick attaching/detaching of fittings. The Spike+ line is for the most serious homebrewers! While designing the setup of the kettle, Spike Brewing offset the ports on these kettles, so you have ample room to use our butterfly valves, or other accessories, with ease. Kettle Features: 2.5 – 6 gallon batch 304 (18/8) stainless steel Sanitary welded coupler design (done at Spike Brewing's facility in Milwaukee, WI) 1.2mm thick walls (thickest on the market) 5mm tri-clad bottom (induction capable) Internal volume markings Polished finish 13.8¨ wide by 17.0¨ tall Domed bottom design Bottom coupler 2" off the bottom (1.25 gallon mark) Top coupler 4" off the bottom (2.5 gallon mark) Staggered design keeps the top port submerged with half batches Lid is included Pictured Ball Valve and Thermometer Sold Separately. Limited availability in store. Drop ships from vendor.
$363.00
CF15 SPIKE CONICAL UNITANK Spike Brewing has completely re-designed their stainless conical line from the ground up. It took a year in the making and are confident that these are the best conical fermenters on the market! Along with the new TC100 Temp Control System, you'll have everything you need to Elevate Your Brew Day! CF15 Features: 304 stainless steel; 1.2mm (18ga) All sanitary welded ports (no-weldless fittings) All hardware shown here is included! Designed for 5 gallon to 1/2 bbl batches 18 gallon total capacity 15 psi working pressure (always use a 15 psi pressure relief valve) Use for pressure transfers Use as a brite tank Etched volume markings 17" wide by 39¨ tall Fully polished finish Lid Features: 4" TC modular top port Allows for hop additions, temp control coil, top sight glass, etc Three 1.5" TC ports which allow for: Blow Off Port – Dedicated port for an airlock or blow off tube Hop Port – Dedicated port for adding hops PRV Port – Dedicated port for your pressure relief valve (PRV) Stainless band clamp for attaching the lid Completely removable lid for easy cleaning Body Features: Huge 2" TC bottom dump with butterfly valves (no more stuck yeast dumps) 1.5" TC racking port with butterfly valve 1.5" TC sample valve (for taking gravity readings) 1.5" TC thermowell with 3" dial thermometer Limited availability in store. Drop ships from vendor.
$1,897.50
Since most brewers who keg use ball lock connections for hooking up their CO2 tank we figured why not design a ball lock fitting to easily add CO2 to your conical! The Spike Brewing gas post assembly has a standard ball lock gas post on one end with a 1/4" NPT on the other. This allows it to screw directly into Spike Brewing carb stone as well as the their gas manifold. Specifications: Stainless steel Ball lock x 1/4" NPT Comes with replacement o-ring
$11.00
When pressurizing your Spike Conical you'll always want to use a pressure relief valve (PRV). This will prevent the tank from being over pressurized and causing a potential failure to occur. This Spike Brewing PRV was developed with their OEM specifically to work with their CF series Conical. It will keep your tank below the 15psi max working pressure rating. The PRV also has a handy bleeder pull ring to release built up pressure. Specifications: 15 psi release 1/4" npt threads Spike Brewing's specially designed gas manifold is also now available.
$25.00
If you didn't already know the Spike Conical is a unitank! This means it is designed to handle pressures up to 15psi. This capability allows you to add 15psi of pressure needed to carbonate your beer before transferring to your keg. This will reduce carbonation times from upwards of a week down to less than 24hrs. Spike Brewing's carb stone is designed to attach to the outside of the racking port butterfly valve. This means the carb stone can be installed when you need it and won't be sitting inside the tank during the entire fermentation process. This eliminates the chance for the stone to become clogged. It also has a protective stainless housing which prevents damaging the very brittle 'stone'. Detailed product guide:Product Guide.pdf Forced carbonation pressure chart:Carbonation Chart Carb Stone Only Carb Stone 1.5" TC Clamp 1.5" TC Gasket Gas Post Carb Stone Bundle Carb Stone Package (see above) Pressure Gauge (Link) PRV (Link) 2nd Gas Post (Link) Gas Manifold (Link) **Always use a 15psi pressure relief valve when pressurizing a tank**
$85.00 - $160.00
Spike Brewing's custom bracing shelf is made in the USA and is a recommended addition when casters or leg extensions are installed for additional stability. Their bracing shelf will also come in handy as a storage shelf for blowoff buckets, tools and more. Specifications: 304SS Super thick 14ga material Made in the USA Bracing shelf install and instructions:Install + instructions
$45.00 - $50.00
Connect a 4" TC fitting to a 1.5" TC fitting with this reducer. Made from 304 stainless steel.
$37.99
FDA approved EPDM gaskets for all your sample needs. Go get yourself a new gasket and seal that baby right up!
$2.50
The Spike+ side pickup is specially designed to work with Spike Brewing's Spike+ line of kettles. The dual 1.5" TC flange allows the pickup tube to attach to the kettle and have a valve or other 1.5" TC accessory attached to the outside. They use 5/8" tubing which flows up to 4x better than their competitors 1/2" size. Recommend Uses: Boil Kettle - Create a whirlpool inside your kettle so hop material collects in the center of the lower stepped section. The side pickup will drain clear wort from the side, above the stepped bottom, avoiding the hop and trub material which has settled. Custom Kettles - Works as a top re-circulation arm or a whirlpool arm. Features: One size fits all Spike+ kettles Oversized 5/8" diameter 304 stainless tube Sized to pick up from above the stepped bottom to avoid hop/trub pickup Rotatable from the outside when installed Made in the USA **A 1.5" gasket and clamp will need to be purchased separately if you do not already have spares**
$34.00
The Spike+ shorty pickup is specially designed to work with Spike Brewing's Spike+ line of kettles. The dual 1.5" TC flange allows the pickup tube to attach to the kettle and have a valve or other 1.5" TC accessory attached to the outside. They use 5/8" tubing which flows up to 4x better than their competitors 1/2" size. Features: One size fits all Spike+ kettles Oversized 5/8" diameter 304 stainless tube Sits on the bottom of the kettle for very low volume losses Made in the USA **A 1.5" gasket and clamp will need to be purchased separately if you do not already have spares**
$34.00
These Spike Brewing false bottoms are for use with their standard Spike kettle line that uses NPT fittings. For the standard Spike+ kettle line that uses TC fittings please see HERE. Design Features: All stainless design; no Silicone gasket to make a seal Low profile design; extremely low dead space (<.25gal) Best filtering on the market due to dual stage filter design; 99.9% grain filtering efficiency Pickup tube and push to connect fitting are included False bottom and pick up tube are Made in the USA! 2 Stage Filtering: Stage 1: Filters through top plate's optimally engineered sized laser cut slits Stage 2: Bottom ring supports the grain weight while also filtering the wort again before it reaches the pickup tube **False bottoms are not designed to filter pellet hops in the boil kettle. Instead you'll want to create a whirlpool to center the hop material and then drain using a side pickup (HERE)**
$126.50 - $253.00
This Spike Brewing adjustable face dial thermometer can be orientated 360 degrees so reading the thermometer is easier. This 1/2” NPT Brew Thermometer is ready to screw directly into the kettle. This 2.5” stemmed thermometer can cover 40-220 degree ranges. The 3” glass dial will display all the information you need at a glance and while withstanding the high heat from the burner below. The thermometer also has calibration screw for added accuracy.
$40.00
50 GALLON STAINLESS BREW KETTLE - V4 Spike Brewing has once again re-designed their brew kettle. They make one of the best brewing kettles available on the market. It is the thickest kettle on the market, with US welded fittings (no more weldless fittings) at a factory direct price. Kettle Features: 15 - 32 gallon batch size 304 (18/8) stainless steel Sanitary welded coupler design (done at our facility in Milwaukee, WI) 1.5mm thick walls (50% thicker than competition) 6mm tri-clad bottom (induction capable) Internal volume markings Polished finish 23.6¨ wide by 27.1¨ tall Domed bottom design Bottom coupler 1.5" off the bottom (3 gallon mark) Top coupler 6" off the bottom (12 gallon mark) Lid is included Pictured Ball Valve and Thermometer Sold Separately. Limited availability in store. Drop ships from vendor.
$726.00
30 GALLON STAINLESS BREW KETTLE - V4 Spike Brewing has once again re-designed their brew kettle. They make one of the best brewing kettles available on the market. It is the thickest kettle on the market, with US welded fittings (no more weldless fittings) at a factory direct price. Kettle Features: 10 - 20 gallon batch size 304 (18/8) stainless steel Sanitary welded coupler design (done at our facility in Milwaukee, WI) 1.5mm thick walls (50% thicker than competition) 6mm tri-clad bottom (induction capable) Internal volume markings Polished finish 19.7¨ wide by 24.1¨ tall Domed bottom design Bottom coupler 1.5" off the bottom (2.25 gallon mark) Top coupler 6" off the bottom (8 gallon mark) Lid is included Pictured Ball Valve and Thermometer Sold Separately. Limited availability in store. Drop ships from vendor.
$522.50
20 GALLON SPIKE+ BREW KETTLE Introducing Spike Brewing's new Spike+ line of kettles! Spike+ is just that, an improvement on an already great platform. The Spike+ line draws from the pro side of brewing with the standard use of tri-clamp (TC) fittings. TC fittings do not have any threads and use a gasket and clamp which allows for quick attaching/detaching of fittings. The Spike+ line is for the most serious homebrewers! While designing the setup of the kettle, Spike Brewing offset the ports on these kettles, so you have ample room to use our butterfly valves, or other accessories, with ease. Kettle Features: 6 – 15 gallon batch 304 (18/8) stainless steel Sanitary welded coupler design (done at Spike Brewing's facility in Milwaukee, WI) 1.2mm thick walls (thickest on the market) 5mm tri-clad bottom (induction capable) Internal volume markings Polished finish 17.7¨ wide by 21.4¨ tall Domed bottom design Bottom coupler 2" off the bottom (2.5 gallon mark) Top coupler 4" off the bottom (4 gallon mark) Staggered design keeps the top port submerged with half batches Lid is included Pictured Ball Valve and Thermometer Sold Separately. Limited availability in store. Drop ships from vendor.
$484.00
Spike Brewing conicals come equipped with this 100% sanitary 2” TC butterfly valve. This valve has a squeeze locking/trigger handle that allows for 180 degrees of motion and 13 locking positions.The butterfly valve is the preferred valve for the cold side of brewing instead of ball valves. These butterfly valves have no pockets or crevices for bacteria to hide in. Ball valves can trap liquid between the seals in the internal ball when opening and closing the valve.The handle is a special 'shorty' style which keeps a compact design. This handle is made from extremely durable glass reinforced Nylon which is much lighter than metal handles. Specifications: 2" TC 304SS metal components FDA silicone seals Light and very durable Nylon handle Squeeze trigger with 13 locking positions
$75.00
This square head plug has 1/2" NPT threads and is made from 304 stainless steel. It can be used to plug any of the 1/2" NPT couplers welded onto Spike Brewing kettles.
$7.00
An oxygenation kit specifically designed for homebrewing. Oxygenate your wort easily and conveniently with a precise amount of oxygen rather than leaving it to chance. The Spike Oxygenation (O2) Kit was designed to provide homebrewers with a simple solution for oxygenating their wort prior to fermentation; Happy yeast = happy beer! The days of slow or failed fermentations are over, and a giant 10lb oxygen tank is no longer the only solution! The O2 kit is designed to attach to a standard hardware store oxygen tank and will precisely oxygenate your wort to make sure fermentation goes smoothly! With that precise flow control, eacg oxygen bottle will oxygenate up to 200 gallons of wort; saving you time and money!
$85.00
Spike Brewing's special 5/8" pickup tube flows up to 4x better than their competitors 1/2" size. These 5/8" tubes work perfectly with their full port valves which have a 5/8" flow diameter; no flow restriction. Spike Brewing's proprietary fittings uses quick connect technology. The quick connect fitting simply hand screws into the kettle and the pickup tube easily pushes in/pulls out; no tools needed. Recommend Uses: Boil Kettle - Create a whirlpool inside your kettle so hop material collects in the center of the lower stepped section. The side pickup will drain clear wort from the side, above the stepped bottom, avoiding the hop and trub material which has settled. Custom Kettles - Works as a top re-circulation arm or a whirlpool arm. Features: One size fits all kettles Large 5/8" diameter 304 stainless tube Simply push in for seal; no tools required Proprietary stainless push to connect fitting included Rests on top step for clear wort draining Made in the USA
$33.00
Want some additional leveling adjustment for your FLEX? Well the Spike Brewing non-marking leveling feet will do the trick! They also use a 304SS stud because nobody likes rust! Specifications: Non marking plastic bottom 304SS stud 3 pack
$16.00
