Spike Brewing
Insulated Tubing
Another Spike innovation that we think solves two big issues. The obvious benefit from insulated lines is increasing your cooling efficiency from your glycol lines. The other benefit is the elimination of line 'sweating'. No more pools of water on your floor during those hot Summer days! *Sold in 6ft increments* Specifications: FDA approved, super flexible PVC tubing 3/8" ID x 1/2" OD tubing 3/8” ID matches temp coil ID; no flow restrictions in the system 3/4" thick flexible insulation Eliminates line sweating and dripping onto your floor Easily connects to our temp control coil with the new Spike Brewing quick connect fittings Made in the USA Detailed TC-100 product guide:Product Guide.pdf
$30.00
1.5" TC x 5/8" OD Barb
Not all hose barbs are created equal! The Spike Brewing special 1.5" TC x barb fitting features a shorter profile and over sized diameter barb. The over sized barb (5/8" OD) is specially designed for 1/2" Silicone tubing. The larger size does two things: It stretches the tubing over the barb creating a tight fit requiring no hose clamps. The inside diameter of our barb is 1/2" compared to standard 1/2" barbs which have a smaller 3/8" size. This creates a full port design and will not restrict flow going through the barb. Specifications: 304SS 1.5" TC x 5/8" barb 1/2" ID
$14.00
Quick Connect Fitting - MQC x MNPT
Out of all the ways to attach silicone tubing to your brew kettle we like quick connect ball lock fittings the most. The ease of connecting/disconnecting and cleaning is unmatched by standard hose barbs, cam locks or tri-clamps. These fittings can easily be attached using one hand even with heavy brewing gloves. The inside diameter of our QC fitting is 1/2". This creates a full port design and will not restrict flow going through the barb. Specifications: 304SS 1/2NPT x QC 1/2" ID
$9.99
Quick Connect Fitting - FQC x Barb
Out of all the ways to attach silicone tubing to your brew kettle we like quick connect ball lock fittings the most. The ease of connecting/disconnecting and cleaning is unmatched by standard hose barbs, cam locks or tri-clamps. These fittings can easily be attached using one hand even with heavy brewing gloves. The over sized barb (5/8" OD) is specially designed for our 1/2" silicone tubing. The larger size does two things: It stretches the tubing over the barb creating a tight fit requiring no hose clamps. The inside diameter of our barb is 1/2" compared to standard 1/2" barbs which have a smaller 3/8" size. This creates a full port design and will not restrict flow going through the barb. Specificatioins: 304SS 5/8" barb x QC 1/2" ID
$17.00
1.5" TC Butterfly Valve
This 1.5” TC butterfly valve can be used on Spike+ kettles. This valve has a squeeze locking/trigger handle that allows for 180 degrees of motion and 13 locking positions.The handle is a special 'shorty' style which keeps a compact design. This handle is made from extremely durable glass reinforced nylon which is much lighter than metal handles. Specifications: 1.5" TC 304SS metal components FDA silicone seals Light and durable fiber reinforced nylon handle Squeeze trigger with 13 locking positions
$65.00
All-In-One PRV
Spike Brewing's The All-In-One PRV is fully adjustable from 0-15psi which allows for use with everything from pressure fermenting to spunding to pressure transfers to a keg! Not only does the All-In-One have an adjustable pressure release but it also has a set 1psi vacuum release! Specifications: Adjustable pressure relief from 0-15psi Built in vacuum release 1.5" tri-clamp connection (2) 1/4" NPT connections for gas post and pressure gauge Pressure gauge and ball lock gas post included Sanitizer cup with drain port Quick pressure relief plunger For use on up to 3bbl fermenters User Guide Link
$145.00
Quick Connect Fitting - MQC x FNPT
Out of all the ways to attach silicone tubing to your brew kettle we like quick connect ball lock fittings the most. The ease of connecting/disconnecting and cleaning is unmatched by standard hose barbs, cam locks or tri-clamps. These fittings can easily be attached using one hand even with heavy brewing gloves. The inside diameter of our QC fitting is 1/2". This creates a full port design and will not restrict flow going through the barb. Specifications: 304SS 1/2NPT x QC 1/2" ID
$9.99
Temperature Control Coil
These USA made temp control coils are specifically designed for the CF series conicals and extend far enough into the conical to temp control both full and half batches. Used in conjunction with a temp controller our temp control coil will help manage your fermentation temps, allow for lagering and cold crashing.The Spike Brewing temp coil simply drops through the top of the lid and quickly attaches with a standard TC clamp. This is a huge improvement over conicals using coils mounted in the side wall. This quick attaching method allows you to lift the coil up slightly to pitch yeast, add hops, etc. The coils are spaced with a sufficient gap for easy cleaning. Simply CIP the conical or soak in brewery wash to easily clean. The temp coil is also a part of Spike Brewing's TC100 Temp Control System and Flex TC100 Bundle that includes everything you need to control your fermentation temperatures! Detailed TC-100 product guide:Product Guide.pdf Specifications: 4" TC 304SS 3/8" tubing Specifically designed for each size Made in the USA Limited availability in store. Drop ships from vendor.
$100.00 - $110.00
TC Thermometer
The Spike Brewing 1.5" TC thermometer will connect directly to the 1.5" port on your kettle. There is no need for a thermowell which allows for quicker more accurate temp readings. It can be used with direct fired kettles but avoid having the flame lapping directly onto the thermometer. **A 1.5" gasket and clamp will need to be purchased separately if you do not already have spares** Specifications: 1.5" TC connection 3" dial 304SS 2.5" stem length Hermetically sealed Calibration adjustment screw
$35.00
2" TC x QC (Quick Connect)
Out of all the ways to attach silicone tubing to your brew kettle or conical, quick connect ball lock fittings are a great option. The ease of connecting/disconnecting and cleaning is unmatched by standard hose barbs or cam locks. These fittings can easily be attached using one hand even with heavy brewing gloves. The inside diameter of this quick connect fitting is 1/2". This creates a full port design and will not restrict flow going through the barb. Specifications: 304SS 2" TC x QC 1/2" ID
$18.00
2" TC Sight Glass
The Spike Brewing engineers have totally redesigned the 2" TC sight glass from the ground up! Standard sight glasses use 4 long bolts that need to be tightened in a criss-cross pattern to get even pressure to avoid leaks. Their new design is made up of only 5 parts compared to 26 parts in a standard sight glass. No tools are required to assemble or disassemble; simply twist the knurled end cap off. The glass is also protected by the stainless guard which protects the glass from even the clumsiest brewer. The sight glass allows for direct attachment to the bottom port of our conicals. The sight glass allows for monitoring flow, color and clarity. A sight glass is also helpful when collecting yeast. Specifications: 2" TC 304 stainless steel Extra thick Pyrex glass 6” long 25% lighter than previous design **A 2" gasket and clamp will need to be purchased separately if you do not already have spares**
$75.00
Thermometer - Non Adjustable Face
This Spike Brewing 1/2” NPT Brew Thermometer is ready to screw directly into the kettle. This 2.5” stemmed thermometer can cover 40-220 degree ranges. The 3” glass dial will display all the information you need at a glance and while withstanding the high heat from the burner below. The thermometer also has calibration screw for added accuracy.
$30.00
2'' 90° TC Elbow
This is the same elbow featured on the bottom of the Spike Brewing conical line. Specifications: 2" TC 304SS
$21.00
2" TC x 5/8" OD Barb
Not all hose barbs are created equal! The Spike Brewing special 2" TC x barb fitting features a shorter profile and over sized diameter barb. The over sized barb (5/8" OD) is specially designed for 1/2" Silicone tubing. The larger size does two things: It stretches the tubing over the barb creating a tight fit requiring no hose clamps. The inside diameter of our barb is 1/2" compared to standard 1/2" barbs which have a smaller 3/8" size. This creates a full port design and will not restrict flow going through the barb. Specifications: 304SS 2" TC 5/8" OD 1/2" ID
$16.00
Racking Arm
Another cool product the Spike Brewing engineers and in-house welders developed is their USA made racking arm. This racking arm provides 6" of total travel allowing you to draw clear wort even with the hoppiest of beers.The racking arm also incorporates a position indicator that is welded on so the orientation of the racking arm can easily be seen from the outside of the sealed conical (especially useful in closed pressure transfers). Specifications: 1.5" TC 304SS Position indicator Works with every size conical Made in the USA **A 1.5" gasket and clamp will need to be purchased separately if you do not already have spares**
$40.00
Leg Extension Set
**Not for use with the CF30** The shorty leg extensions are 9” long (compared to 18”). They were specifically designed to be used with the 2” sight glass in the vertical arrangement. This was the major design criteria that Spike Brewing engineering noticed.The long leg extensions were specifically designed to bring the racking port to a height where the conical can be gravity drained into a 5 gallon corny keg. However they are pretty long for those people that do not need to gravity transfer but want the conical high to use a sight glass for example. *It is recommend to use the standard or extended bracing shelf when using the leg extensions for added stability* Shortly leg extension specifications: 304SS 9" long Top threads for attaching to conical legs Bottom threads for attaching leveling feet and casters Long leg extension specifications: 304SS 18" long Top threads for attaching to conical legs Bottom threads for attaching leveling feet and casters
$45.00 - $60.00
Insulated Conical Jacket
Spike Brewing's insulated conical jacket uses high quality, extra thick, yet flexible neoprene material to insulate your conical from the worst ambient conditions be it a hot garage or cold basement. Each custom designed, hand stitched (in the USA) jacket is custom tailored to fit each size of Spike Brewing's conical line. Their jacket was designed by a former Lululemon designer because if you're going to cover up shiny stainless steel it better look amazing. We think she did the trick! Specifications: Sewn in the USA (of imported fabric from Japan and China) Reinforced stitching around all ports, legs and handles for extra strength Helps maintain stable fermentation temps regardless of ambient conditions Stops the tank from ‘sweating’ in warm weather Interior Velcro for attaching the optional heater Machine washable Detailed TC-100 product guide:Product Guide.pdf Limited availability in store. Drop ships from vendor.
$100.00 - $145.00
1.5" TC x 5/8" OD 90° Barb
This elbow will connect to any 1.5" TC port. It features an oversized barb designed to use with 1/2" tubing. This creates a full port opening for unrestricted flow and a tight seal that requires no hose clamps. Specifications: 1.5" TC 304SS Oversized 90 degree barb for 1/2" tubing
$17.00
Closed Pressure Transfer Kit
Introducing another cool accessory to compliment Spike Brewing CF series conicals. Their closed pressure transfer kit (CPT kit) will allow you to rack your beer from your conical to keg without exposing it to oxygen. This will help you avoid off-flavors that can be caused by oxygen coming in contact with your beer. The Spike Brewing CPT kit uses all stainless hardware and Ultra Barrier tubing which is antibacterial due to its silver lining. It is also BPA free and over-sized to promote a quick transfer from conical to keg. CPT Kit Includes: 1.5" TC to flare 1.5" TC clamp 1.5" TC gasket Flare to liquid ball lock Gas ball lock blow off The Spike Brewing gas manifold bundle can be seen HERE.**Always use a 15psi pressure relief valve when pressurizing a tank****
$65.00
1.5" TC x QC (Quick Connect)
Out of all the ways to attach silicone tubing to your brew kettle or conical, quick connect ball lock fittings are a great option. The ease of connecting/disconnecting and cleaning is unmatched by standard hose barbs or cam locks. These fittings can easily be attached using one hand even with heavy brewing gloves. The inside diameter of this quick connect fitting is 1/2". This creates a full port design and will not restrict flow going through the barb. Specifications: 304SS 1.5" TC x QC 1/2" ID
$17.00
Flex+
FLEX+ FERMENTER Introducing the new Spike FLEX+! The FLEX+ was designed to be the most versatile, upgradable and longest lasting small batch fermenter on the market. With currently over 20 accessories (and counting) you'll never run out of run toys to bling your FLEX out with. The FLEX+ is the big brother to the standard FLEX. Out of the box it features an upgraded tri-clamp racking arm, tri-clamp butterfly valve and upgraded high pressure lid and clamp that can handle up to 15 psi. The higher pressure rating allows for carbonating your beer in the same tank you fermenter in. Carbonate your beer in 24hrs opposed to 7 days!All hardware shown HERE is included! Flex Features: 304 stainless steel; 1.2mm (18ga) All sanitary welded ports (no-weldless fittings) Designed for 2.5 to 6 gallon batches 7 gallon total capacity 15 psi working pressure Use for pressure transfers Use as a brite tank Etched volume markings Fully polished finish Dimensions: 15" wide by 21¨ tall (to top of airlock) See additional dimensions here Lid Features: 4" TC modular top port Allows for hop additions, temp control coil, top sight glass, etc Three 1.5" TC ports which allow for: Blow Off Port – Dedicated port for an airlock or blow off tube Hop Port – Dedicated port for adding hops PRV Port – Dedicated port for your pressure relief valve (PRV) Stainless band clamp for attaching the lid Completely removable lid for easy cleaning Body Features: 1.5" TC racking port with rotatable racking arm 1.5" TC secondary port for thermometer, sample valve, etc Limited availability in store. Drop ships from vendor.
$450.00
Blow-Off Cane
This USA made blow off cane is designed to attach to the 1.5" TC on the lid of the Spike Brewing conicals. Options:Standard: For use as a standard blow off into sanitizer 1.5" TC End: Use for a blow off into sanitzer with a barb (HERE) and/or attach the Spike Brewing pressure manifold (HERE). Specifications: 1.5" TC 304SS 15” total drop Works with every size conical Made in the USA
$45.00 - $65.00
Conical Heater
Unfortunately some of us will have to heat our conicals during the long Winter months. No fear, Spike Brewing has the solution! Each conical has its own sized heater and the wattage of each is carefully designed to match it. They also use a built in thermostat which stops the heater from getting too warm. This means you get a gentle warming action when your beer drops below your desired temp (opposed to rapid heating which can overshoot or 'cook' your beer). This heater attaches to Spike Brewing's insulated conical jacket via Velcro. It rests on the bottom cone section of the conical where the coldest liquid is. This will give the most even temperature throughout your fermenter (happy yeast!). Specifications: Different wattages for each fermenter (ranging from 80w to 150w) Built in 90F thermostat to prevent the heater from overheating your wort 5' long cord Detailed TC-100 product guide:Product Guide.pdf Limited availability in store. Drop ships from vendor.
$100.00 - $130.00
1.5" TC Thermowell
Spike Brewing's thermowell features a 1/4" temp probe opening on the outside which is mounted to a 1.5" TC fitting. This allows it to attach directly to the sanitary TC fitting on the conical. It also allows for an optional digital temp sensor to be attached. The probe is completely sealed from the outside. Pro Tip:The thermowell can be packed with thermal grease to help temperature response times. Specs: 1.5" TC 304SS 4” long 0.250" ID
$30.00
Temperature Coil Connect Fittings
At Spike Brewing, they love quick connect fittings. Why use tools when you don't need to? These 90° quick connect fittings will make attaching insulated tubing to your temp coil a breeze. Specifications: Connect your temp coil to your insulated tubing without tools 3/8" to 1/2" connections 90° design; prevents glycol lines from kinking 2 fittings included per purchase Detailed TC-100 product guide:Product Guide.pdf
$18.00
4" TC Clamp
A standard clamp for all of Spike Brewing's 4" TC ports Specifications: 4" TC 304SS
$15.00
4" Clear TC Cap
Probably the coolest add-on for the Spike Brewing conical line! There heard many brewers who have switched from clear carboys to stainless and they only have one complaint; I can't see my beer fermenting any more! Brewers are curious by nature and we're not ones to stop that curiosity so here is our solution to that problem.Their engineers designed a clear polycarbonate (same material as bullet proof glass) cap which allows you to see inside the top of the conical when it's fermenting. This has also been tested against common brewery chemicals and has held up against the likes of PBW and StarSan. Specifications: 4" TC Clear polycarbonate material
$33.00
1.5" TC Sight Glass
The Spike Brewing engineers have totally redesigned the 1.5" TC sight glass from the ground up! Standard sight glasses use 4 long bolts that need to be tightened in a criss-cross pattern to get even pressure to avoid leaks. Their new design is made up of only 5 parts compared to 26 parts in a standard sight glass. No tools are required to assemble or disassemble; simply twist the knurled end cap off. The glass is also protected by the stainless guard which protects the glass from even the clumsiest brewer. The sight glass allows for direct attachment to the bottom port of our conicals. The sight glass allows for monitoring flow, color and clarity. A sight glass is also helpful when collecting yeast. Specifications: 1.5" TC 304 stainless steel Extra thick Pyrex glass 5” long 25% lighter than previous design **A 1.5" gasket and clamp will need to be purchased separately if you do not already have spares**
$65.00
CIP Ball
Another cool innovation from the Spike Brewing engineers; their low pressure CIP ball! They wanted to design a CIP ball that didn’t require home brewers to purchase another pump if they already owned one. Small brewery pumps, like Chugger and March pumps used on our Spike System, are very common for most home brewers. However, most CIP balls require a much larger pump to work properly. This CIP ball was specifically designed to work with the more common 7GPM pumps. It has also been tested with larger sump pumps which are also commonly used for CIP applications. Spike Brewing also designed the CIP ball to fit through a 1.5" TC port. This allows for quick install of the CIP ball after fermentation. This works especially well with cleaning the temp control coil. They recommend a 5-10min CIP with 160F brewery wash to give a nice and shiny FLEX or conical fermenter. Pro Tip:If you do not have a FLEX+ lid with 1.5" TC port you can attach the CIP ball to the secondary port of your FLEX after an initial dump and rinse. Then simply CIP as described above! Specifications: 1.5" TC x 1.5" TC 304SS Low flow design
$70.00
Gas Manifold Bundle
Spike Brewing's specially designed CO2 gas manifold is designed to attach directly to the 1.5" TC port on your fermenter's lid. This manifold allows you to easily add pressure for transfers, stuck yeast dumps, purging oxygen, carbonating, etc. The manifold has 3 ports for a pressure gauge, pressure relief valve and a ball lock gas post. One part, three functions, easy assembly, easy cleaning; what more could you ask for!? Gas Manifold Bundle: Gas Manifold Pressure Gauge (Link) PRV (Link) Gas Post (Link) **Always use a 15psi pressure relief valve when pressurizing a tank**
$85.00
Stainless Steel Ball Valve - 3 Piece
Spike Brewing's 1/2” stainless steel ball valve screws directly into our brew kettles, no need for an additional nipple to make the connection like competitors valves. This valve is dual sided with a male (which screws directly into your kettle) and a female end (which allows for a 1/2" barb or other 1/2" fitting). The 3 piece valve completely disassembles so a thorough cleaning is easy. Specifications: Made from 304 stainless steel 1/2" NPT male end screws directly into the kettle Full port 5/8” inner diameter
$30.00
Quick Connect Replacement O-Rings
Set of 3 replacement o-rings for quick connect fittings. Specifications: Silicone o-ring Sold in set of 3
$3.00
FLEX Heater
Unfortunately some of us will have to heat our FLEX during the long winter months. No fear, we have the solution! The FLEX heater was carefully engineered to match the heating needs to maintain set temperatures even in the coldest winter garage. It also uses a built in thermostat which stops the heater from getting too warm. This means you get a gentle warming action when your beer drops below your desired temp (opposed to rapid heating which can overshoot or 'cook' your wort). This Spike Brewing heater attaches to their insulated FLEX jacket via Velcro. It is positioned near the bottom cone section of the fermenter where the coldest liquid is. This will give the most even temperature throughout your fermenter (happy yeast!). Specifications: Built in 90F thermostat to prevent the heater from overheating your wort 80 watts of power Durable silicone construction 5' long cord Detailed TC-100 product guide:Product Guide.pdf
$70.00
Cooling Pump
All pumps are not equal! The Spike Brewing engineers tested over 15 pumps during the development of this project and found almost all small submersible pumps on the market are grossly overrated. This can greatly affect your temperature control as flow rate is directly proportional to cooling efficiency. To use: Simply plug our pump into our temp controller Connect your insulated lines to your temp control coil and to the pump outlet Submerse the pump in your cooler (with ice), fridge with cold water reservoir or glycol chiller Start cooling your wort! Specifications: High flow submersible pump 3/8" barbed outlet (connect directly to our insulated tubing) 12v DC powered (much safer than AC submersible pumps) Suction cups to keep pump submerged Detailed TC-100 product guide:Product Guide.pdf
$45.00
Steam Condenser Lid
Built to transform steam into liquid during the boil, Spike Brewing's steam condenser lid will enable you to brew inside without worrying about moisture collecting on your walls and ceiling, which can cause mold issues. These lids are not only designed to fit Spike kettles, but will also work with most other kettle brands on the market. From a better boil-off rate to major cost savings and conveniences, you will find many benefits by adding this to your brew setup. Features & Specs: Compared to boiling without a lid, the Steam Condenser Lid has a 50% reduced boil-off rate and results in a ~6% total boil-off. Replaces the need to install a hood for indoor brewing Prevents mold from forming on walls and ceiling Third-party lab tested to show that DMS is completely undetectable (under 25 ppb) after only 30-45 minutes of boiling Discharge water is very hot and can be used for cleaning Compatible with Spike Kettles and the Spike Solo 1.5" tri-clamp port for CIP ball 4" tri-clamp port for hop additions Water usage: 15 gallons/hour for 10g, 15g & 20g lids 25 gallons/hour for 30g &. 50g lids Lid, pump, condenser mister, piping, clamps, gaskets, barbs & caps included with purchase For more information, see Spike Brewing's FAQ. To get started using the lid, see our Steam Condenser Lid Product and Process guides. Note: Limited inventory availability in-store. Sizes not carried in-store will be drop shipped from the vendor.
$360.00 - $475.00
10 Gallon Spike Brewing Kettle - V4, Vertical Couplers
10 GALLON STAINLESS BREW KETTLE - V4 Spike Brewing has once again re-designed their brew kettle. They make one of the best brewing kettles available on the market. It is the thickest kettle on the market, with US welded fittings (no more weldless fittings) at a factory direct price. Kettle Features: 2.5 - 6 gallon batch size 304 (18/8) stainless steel Sanitary welded coupler design (done at our facility in Milwaukee, WI) 1.2mm thick walls (thickest on the market) 5mm tri-clad bottom (induction capable) Internal volume markings Polished finish 13.8¨ wide by 17.0¨ tall Domed bottom design Bottom coupler 1.5" off the bottom (1 gallon mark) Top coupler 6" off the bottom (4 gallon mark) Lid is included Pictured Ball Valve and Thermometer Sold Separately. Limited availability in store. Drop ships from vendor.
$285.00