Draft Fittings
Hex Nut Washer
Flat neoprene washer for use with beer shanks or Sanke couplers. Pairs up with a tailpiece and hex nut (or wing nut).
$0.85 - $6.49
Flare Swivel Nut & 5/16" Swivel Stem
Swivel nut and stem set. Used to attach 5/16" ID draft or CO2 line to corny keg disconnects. Barb Specifications: Material: Stainless Steel Size: 5/16" Nut Specifications: Material: Brass Finish: Chrome Plated Brass Size: 1/4"
$2.99
Flare Swivel Nut with 1/4'' Stem
Swivel nut and stem set. Used to attach 3/16" ID or 1/4" ID draft line to corny keg disconnects. Barb Specifications: Material: Stainless Steel Size: 1/4" Nut Specifications: Material: Brass Finish: Chrome Plated Brass Size: 1/4"
$2.99
Hex Nut for Tailpiece
Nickel Plated Brass Hex Nut, 1" (Beer Thread, 29/32-14). Used to connect a tailpiece to a sanke coupler or a shank. You may also need a tailpiece or hex nut washer. California Proposition 65 Warning: This product may contain a chemical known to the State of California to cause cancer, or birth defects, or other reproductive harm.
$1.95
Duotight 8 mm (5/16 in.) x 1/4 in. Flare
This Duotight fitting with 1/4" Flare is perfect for flared gas and beverage ball lock and pin lock disconnects. This Duotight fitting is compatible with EVABarrier 8 mm OD Tubing. Duotight offers superior quality when compared to other push-in fittings. Their double EPDM O-ring design provides a more complete and reliable seal, protecting against leaks even when tubing is bent around tight corners. They are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines! Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Note: Ball lock fitting and regulator not included.
$4.80
3/16" Stainless Steel Tailpiece (304)
3/16" ID stainless steel tailpiece commonly used for 3/16" ID draft tubing. 304 Stainless Steel
$3.49
Plastic Carbonation and Line Cleaning Cap
This plastic ball lock cap features soda bottle threads, allowing you to convert a soda bottle into a pressurized growler. It is compatible with both gas and liquid ball lock disconnects. Also works well for cleaning draft lines. Simply add line cleaning solution to a soda bottle, attach it to the draft line, and open the faucet to push solution through. When using two ball lock caps, it is recommend pairing this yellow plastic cap with a red plastic cap so you can easily identify which caps are being used for liquid or gas. This cap can also be attached to the FermZilla collection container, enabling you to purge the collection container of oxygen. Specifications: Liquid and Gas Ball Lock Compatible Overall Length - 2.5" Barb Length - 7/8" Barb OD - 1/4" Barb ID - 3/16" 28 mm PCO 1881 Threads
$8.80
Duotight 8mm (5/16) x 5/8 Female Beer Thread
This Duotight to Female Beer Thread fitting can be used to connect beverage line to faucet shanks instead of a tailpiece, and it's also a convenient option for connecting gas and beverage line to the gas in and bev out on keg couplers. Compatible with EVABarrier 8 mm OD Tubing. Duotight offers superior quality when compared to other push-in fittings. Their double EPDM O-ring design provides a more complete and reliable seal, protecting against leaks even when tubing is bent around tight corners. They are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines! Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C)
$4.80
Duotight - 6.5 mm (1/4 in.) x 8 mm (5/16 in.) Reducer
Duotight offers superior quality when compared to other push-in fittings. Their double EPDM O-ring design provides a more complete and reliable seal, protecting against leaks even when tubing is bent around tight corners. They are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines! Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C)
$2.80
Duotight 8 mm (5/16 in.) Check Valve
This Duotight check valve is a great idea for protecting your regulator. It has a low opening pressure of 1 psi, and since it cannot be opened or taken apart, it is recommended for gas applications only. The internal components are made from stainless steel. Compatible with EVABarrier 8 mm OD Tubing. Duotight offers superior quality when compared to other push-in fittings. Their double EPDM O-ring design provides a more complete and reliable seal, protecting against leaks even when tubing is bent around tight corners. They are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines! Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C)
$5.00
Flare Swivel Nut & Swivel Stem (3/16" OD)
Swivel nut and barb for connecting 1/8" ID tubing to a 1/4" flare fitting. Barb Specifications: Material: Stainless Steel Size: 3/16" OD Nut Specifications: Material: Brass Finish: Chrome Plated Brass Size: 1/4" Flare
$2.25
5/16'' Gas Hose Barbed Tee, Chrome Plated
Chrome plated Brass splicer tee has a 5/16″ bore. So use with 5/16 in. ID inlet and outlet hoses. Barbed Hose splicer Tee for gas in beer dispensing Brass with chrome plating. Tee fittings turn it to a 3-way system. Use with 5/16″ ID hoses.
$4.75
Stainless Carbonation and Line Cleaning Cap
This stainless steel ball lock cap features soda bottle threads, allowing you to convert a soda bottle into a pressurized growler. It is compatible with both gas and liquid ball lock disconnects. Also works well for cleaning draft lines. Simply add line cleaning solution to a soda bottle, attach it to the draft line, and open the faucet to push solution through. This is a direct replacement to ball lock fittings included with the FermZilla pressure kit. It can also be attached to the FermZilla collection container, enabling you to purge the collection container of oxygen. 28mm PCO 1881 Threads
$15.50
Duotight 8 mm (5/16 in.) Tee
This Duotight tee fitting is compatible with EVABarrier 8 mm OD tubing. Duotight offers superior quality when compared to other push-in fittings. Their double EPDM O-ring design provides a more complete and reliable seal, protecting against leaks even when tubing is bent around tight corners. They are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines! Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C)
$3.30
Tailpiece, Threaded, 1/4mfl
Stainless steel 1/4" mfl tailpiece.
$7.39 $4.99
Hose Tailpiece For 5/16'' Tubing
5/16" Hole, 3/8" Barb Shank TailpieceShank Tailpiece for 5/16" ID HoseNickel Plated
$2.00
Duotight Removal Tool and Tube Cutter
This 2-in-1 tubing cutter is hard to beat for clean, straight cuts. It is developed specifically for EVABarrier draft line, but is also compatible with any tubing that is 3/8" OD or smaller. Features a 8mm jaw on the back of the unit to easily pull the collet back when removing tubing from Duotight fillings.
$6.60
3/8'' Barbed Tee, Stainless Steel
3/8” barbed tee, stainless steel.
$3.99
Duotight 8 mm (5/16 in.) Ball Valve
This Duotight ball valve can be used as an inline shut off valve on draft lines. Compatible with EVABarrier 8 mm OD Tubing. Duotight offers superior quality when compared to other push-in fittings. Their double EPDM O-ring design provides a more complete and reliable seal, protecting against leaks even when tubing is bent around tight corners. They are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines! Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C)
$3.90
1/4” x 1/4” Splicer, 304 S/S
1/4" X 1/4" hose splicer (for 1/4" ID hose) 304 Stainless Steel
$3.49
1/4'' ID Stainless Steel Tailpiece
1/4" ID, 5/16 OD Tailpiece Stainless Steel
$3.49
Flare Fitting, 1/4" Male Flare x 1/4" Barb
1/4" male flare fitting to 1/4" barb. Commonly used with cold plates. Barb will fit 3/16" ID or 1/4" ID tubing.
$4.49
Elbow Tailpiece, 3/16'' Barb, Stainless Steel
Stainless steel elbow tailpiece with 3/16" Barb
$6.95
KOMOS® Silicone Tailpiece Gaskets - 10 Pack
5/8" silicone tailpiece gaskets for draft shanks or keg couplers. 10 Pack of washers.
$5.99
Stainless Steel Check Valve
Stainless steel check valve 1/4" male flare(mfl) to 1/4"female flare(ffl) fittings
$11.95
1/4” x 5/16” Splicer, Stainless
Splice together 1/4" ID and 5/16" ID tubing with this 303 stainless steel hose splicer.
$3.99
1/4'' Barbed Tee, Stainless Steel
1/4” barbed tee, stainless steel.
$2.75
Co2 Disconnect Nipple with Hose Barb
If you use different kegs and couplers on a normal basis, save time by add quick disconnects to your draft systems gas line tubing. Place a quick disconnect fitting in the gas line and no tools are needed to disconnect from the gas source. Simply pull back the sleeve on the female side and the connection separates and the gas is shut off. Note: To make a complete set please order the Disconnect Air Coupler. Specifications: Connection: Male Side Length: 2" Barb: 3/8" O.D. (to fit 5/16" I.D. Gas Hose) Material: Brass, anodized
$6.99
Stainless Carbonation and Line Cleaning Cap - Duotight Compatible
This stainless steel ball lock cap features soda bottle threads, allowing you to convert a soda bottle into a pressurized growler. It is compatible with both gas and liquid ball lock disconnects. Also works well for cleaning draft lines. Simply add line cleaning solution to a soda bottle, attach it to the draft line, and open the faucet to push solution through. This is a direct replacement to ball lock fittings included with the FermZilla pressure kit. It can also be attached to the FermZilla collection container, enabling you to purge the collection container of oxygen. 28mm PCO 1881 Threads This version features a 6.5mm Duotight compatible stem. Use the 8mm or 9.5mm reducer to attach EVABarrier draft line.
$15.50
Elbow Tailpiece, 1/4'' Barb, Stainless Steel
Stainless Steel tailpiece with 1/4" barb.
$6.95
3/8” x 3/8” Splicer - Stainless Steel
Beer line 3/8" x 3/8" stainless steel barbed splicer. Splices 5/16" I.D. Vinyl to 5/16" I.D. Vinyl 5/16" I.D. Vinyl to 3/8" I.D. Poly 3/8" I.D. Poly to 3/8" I.D. Poly Specifications Type: Straight Connectors Material: 304 Stainless Steel O.D.: 3/8" I.D.: 1/4"
$3.99
Duotight - 8 mm (5/16 in.) x 9.5 mm (3/8 in.) Reducer
This Duotight reducer is used when stepping down from 9.5 mm OD to 8 mm OD EVABarrier tubing. Duotight offers superior quality when compared to other push-in fittings. Their double EPDM O-ring design provides a more complete and reliable seal, protecting against leaks even when tubing is bent around tight corners. They are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines! Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C)
$3.30
5/16''x 3/8'' Splicer - Stainless Steel
Beer line 5/16" x 3/8" stainless steel barbed splicer. Splices 1/4" I.D. Vinyl to 5/16" I.D. Vinyl 1/4" I.D. Vinyl to 3/8" I.D. Poly 5/16" I.D. Poly to 3/8" I.D. Poly Specifications Type: Straight Connectors Material: 304 Stainless Steel I.D.: 1/4"
$3.99
1/4'' Beer & Gas Tubing QD Set - In-line W/ Shut-off
These disconnects feature 1/4" barbed fittings that will fit into 3/16", 1/4", or 5/16" ID tubing. The temperature range is -40F to 180F and they can handle a vacuum to 120 PSI. The internal valve spring is made of 316 stainless steel and the o-ring is food grade.
$16.99
Co2 Disconnect Air Coupler
If you use different kegs and couplers on a normal basis, save time by add quick disconnects to your draft systems gas line tubing. Place a quick disconnect fitting in the gas line and no tools are needed to disconnect from the gas source. Simply pull back the sleeve on the female side and the connection separates and the gas is shut off. Note: To make a complete set please order the Disconnect Tailpiece or Disconnect Nipple with Hose Barb. Specifications: Connection: Female Side Length: 3-1/4" Barb: 3/8" O.D. (to fit 5/16" I.D. Gas Hose) Material: Brass Shut-off: Built in
$16.99
Duotight 9.5 mm (3/8 in.) Check Valve
This Duotight check valve is a great idea for protecting your regulator. It has a low opening pressure of 1 psi, and since it cannot be opened or taken apart, it is recommended for gas applications only. The internal components are made from stainless steel. Compatible with EVABarrier 9.5 mm OD tubing. Duotight offers superior quality when compared to other push-in fittings. Their double EPDM O-ring design provides a more complete and reliable seal, protecting against leaks even when tubing is bent around tight corners. They are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines! Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C)
$8.80
