Hardware & Fittings
1/2'' x 1'' SS Nipple, Threaded Close
Stainless steel 1/2" x 1" close nipple. Used for connecting a 1/2" ball valve to a union.
$5.00
Camlock Type B
Type B camlock disconnect fitting. Female camlock with 1/2" Male Pipe Thread (MPT). 304 Stainless steel construction. 150 psi working pressure.
$15.50
1/4" Flare Fitting Tee
Stainless steel tee with 1/4" flare thread on all three ends.
$15.00
Washer - Stainless Steel
This stainless steel washer is specially sized to fit over male NPT fittings. Inner diameter: 0.82" Outer diameter: 1.25" Thickness: ~0.0625"
$1.00
Stainless Nipple - 1/2 in x 2 in Threaded
1/2" MPT(male pipe thread) x 2" length stainless steel nipple. 304 stainless steel.
$4.99
4" Clear TC Cap
Probably the coolest add-on for the Spike Brewing conical line! There heard many brewers who have switched from clear carboys to stainless and they only have one complaint; I can't see my beer fermenting any more! Brewers are curious by nature and we're not ones to stop that curiosity so here is our solution to that problem.Their engineers designed a clear polycarbonate (same material as bullet proof glass) cap which allows you to see inside the top of the conical when it's fermenting. This has also been tested against common brewery chemicals and has held up against the likes of PBW and StarSan. Specifications: 4" TC Clear polycarbonate material
$33.00
1.5'' Tri-Clamp x 3/4'' Female BSPP, Stainless Steel
A 1.5" Tri-Clamp to 3/4" Male Pipe Thread.304 Stainless Steel
$29.00
Hose Stem, 5/16'' Barb, 1/4'' fpt
Brass hose stem. 5/16" barb 1/4" female pipe thread (fpt)
$2.99 $1.99
Quick Connect Replacement O-Rings
Set of 3 replacement o-rings for quick connect fittings. Specifications: Silicone o-ring Sold in set of 3
$3.00
2'' Maximizer for Kettle
2" maximizer allows you to transfer more liquid from your brew kettle. The maximizer will thread into a 1/2" FPT fitting inside your kettle.
$11.95
3/8" Full Port Stainless Ball Valve
304 stainless steel full port ball valve with 3/8" female pipe thread (FPT) on both ends. Note: Handle may be blue instead of the pictured yellow.
$16.50
15 psi Pressure Relief Valve
When pressurizing your Spike Conical you'll always want to use a pressure relief valve (PRV). This will prevent the tank from being over pressurized and causing a potential failure to occur. This Spike Brewing PRV was developed with their OEM specifically to work with their CF series Conical. It will keep your tank below the 15psi max working pressure rating. The PRV also has a handy bleeder pull ring to release built up pressure. Specifications: 15 psi release 1/4" npt threads Spike Brewing's specially designed gas manifold is also now available.
$25.00
Pickup Tube - Shorty
Spike Brewing's special 5/8" pickup tube flows up to 4x better than their competitors 1/2" size. These 5/8" tubes work perfectly with their full port valves which have a 5/8" flow diameter; no flow restriction. Spike Brewing's proprietary fittings uses quick connect technology. The quick connect fitting simply hand screws into the kettle and the pickup tube easily pushes in/pulls out; no tools needed. Features: One size fits all kettles Large 5/8" diameter 304 stainless tube Simply push in for seal; no tools required Proprietary stainless push to connect fitting included Sized to pick up from the bottom edge of the kettle Made in the USA
$30.00
Camlock Type A
Type A camlock disconnect fitting. Male camlock with 1/2" Female Pipe Thread (FPT). 304 Stainless steel construction. 150 psi working pressure.
$9.90
BrewZilla | DigiBoil | Adjustable Lid Clamps | Stainless Steel | Set of 4
Get the exact tension you need with your BrewZilla or DigiBoil with KegLand's Stainless Steel Adjustable Clamp Set. Permanently replace the standard lid clamps and adjust the tension to your needs. These clamps are only intended for use with the metal Distillation Lid or Boiler Extension Kits. If you are having trouble getting the correct tension to form a good seal with those accessories, these adjustable clamps can help you dial in the fit. They should never be used with the standard glass lid. Compatible with 35L and 65L BrewZillas (Gen 3 / Gen 4), DigiBoils (Gen 1 / Gen 2), and Boiler Extensions. Installation Instructions: You will need a pair of bolt cutters or tin snips to cut the standard clamp off. (Please see product photos for optimum cut location). Remove the nut and bolt and thread it through the clamp. Ensure that the grooved part is facing outwards (photo for reference). If you do not have the grooved part facing outwards, the clamp will be blocked by the round lip of the boiler. Loosen the bolts and spin the clamp up or down to adjust the tension. Use the nuts to lock the desired tension. It is always best to start looser than you think, then adjust tighter. Warning: Do not use the adjustable clamps with a glass lid, the clamps are only designed for distillation lids or other metal accessories.
$13.50
ForgeFit® Stainless Tri-Clamp Extension Tube (Spool) - 1.5 in. x 12 in.
304-type stainless steel tri-clamp extension tube with 1.5" clamp ends. 12" long.
$29.00
ForgeFit® Stainless Tri-Clamp Extension Tube (Spool) - 1.5 in. x 5 in.
304-type stainless steel tri-clamp extension tube with 1.5" clamp ends. 5" long. This is the same length as a Tee. It is used to swap instruumentation in and out of an established system.
$25.50
Stainless Tri-Clamp Weldless Bulkhead - 2 in.
Add a 2" tri-clamp port to any tank or lid with this 304 stainless steel weldless bulkhead. Just drill a 45-47 mm hole and tighten this item to your vessel wall. For distilling purposes, this is perfect if you want to fit an extension tube between the BrewZilla / DigiBoil distillation lid and the copper pot or reflux still.
$29.99
4" TC Cap
Cap any 4” port with this stainless steel cap. Specifications: 4" TC 304SS
$16.00
1.5'' Tri-Clamp x 1'' Barb Long Stem, Stainless Steel
A 1.5" Tri-Clamp to 1" barb fitting.304 Stainless Steel
$19.99
Male Garden Hose Fitting with 3/8" Barb
Brass, male garden hose fitting with 3/8" barb for tubing.
$4.99
1/2 in MPT Solid Plug - Stainless
1/2" MPT stainless steel solid plug. Uses a 7/8" wrench.
$5.25
90° Elbow, 1/2'' fpt x 1/2'' fpt, Stainless Steel
90° stainless steel elbow, 1/2" fpt x 1/2" fpt
$5.49
1/2 in. mpt X 3/8 in. Barb Elbow, Stainless
This 1/2 in. mpt X 3/8 in. Barb Elbow is made from corrosion-resistant 304 Stainless steel.
$6.50
1/2 in MPT Hollow Plug - Stainless
1/2" MPT stainless steel hollow plug.
$6.50
Stainless Tri-Clamp Concentric Reducer - 4 in. x 2 in.
Stainless steel Tri-Clamp reducer with 4" T.C. and 2" T.C. connections.
$55.00
1.5'' Tri-Clamp x 1.5'' Barb, Stainless Steel
Barbed fitting for use with tri-clamp systems. This fitting has a 1-1/2 inch TC on one side, 1-1/2 inch barb on the other side. Use with 1-1/2 inch ID hose. The barbed stem is 4-1/2" long. 304 Stainless Steel
$22.00
1.5'' Tri-Clamp x 1'' Barb, Short, Stainless Steel
A 1.5" Tri-Clamp to 1" barb fitting.304 Stainless Steel
$18.95
ForgeFit® Stainless Tri-Clamp End Cap - 3 in.
End cap for 3" tri-clamp fittings. Made from 304 stainless steel.
$6.99
3" Tri-Clamp, Stainless Steel
The most popular choice for sanitary connections, tri-clamp fittings are widely used in the food & beverage industry due to their ability to be cleaned in place. Tri-clamps join two fittings together without any nooks or crannies for contaminants to hide. Use anywhere you want to ensure a sanitary connection. 3" tri-clamp Made from 304 stainless steel
$16.50
Stainless Sight Gauge Adapter w/ plug
Connects a sight glass to a thru-wall or weldless bulkhead fitting.
$23.95
3/4'' FHT x 1/2'' Barb, Stainless Steel
3/4" female hose thread x 1/2" barb, stainless steel
$8.95
TC Sample Valve
Spike Brewing conicals come equipped with this 100% sanitary sample valve. Taking samples has never been so easy; simply twist the valve handle to slowly draw out a sample from your fermenter for a gravity reading. The one downside is you might end up with lower final volumes due to how easy it is to take taste tests ;)Specifications: 1.5" TC 304SS FDA Silicone seals 3/8” barb
$35.00
1.5'' Tri-Clamp Tee
1.5" Tri-Clamp Tee 304 Stainless Steel
$29.95
Pickup Tube Replacement O-Rings
Set of 3 replacement o-rings for the Spike Brewing 5/8" quick connect pickup tube fittings. Specifications: FDA approved Buna-N Sold in set of 3
$2.50
Female Pipe Cross 1/2'' NPT, Stainless Steel
1/2" npt female pipe cross, stainless steel
$7.95
