Best Selling Products

Stan Hieronymus expertly explains the nature of hops, their origins, hop quality and utilization--and even devotes an entire chapter to dry hopping. For the Love of Hops also includes a reference catalog of more than 100 varieties and their characteristics.

Read more less

For use with an in-line plate filter. These pads will provide between .3 - .5 Micron filtration. This pad is the right choice when you want to promote sterility in the bottle, although do please note that the pad does not remove 100% of bacteria - only an absolute rated .45 micron or less cartridge filter can do so. Then why do we sell this pad? Some experienced winemakers who are familiar with their wine and who do not have a cartridge filter use this pad to remove most ml bacteria, making it less likely that an unwanted ML fermentation takes place in the bottle. Each filter pad set is good for approximately 5 gallons of wine when the wine has already been filtered by the polish pads. These pads are disposable.

Read more less

This Duotight plug is used to block up your 8 mm (5/16") tees, elbows or other fittings for gas leak testing or simply to plug an unused section. Features: Insert plug and firmly push to connect Release plug by pushing in the collet on the Duotight fitting Suitable for both gas & beverage applications Made from food-grade acetal plastic Temperature rated to 212°F (100°C)

Read more less

This Duotight joiner fitting is compatible with EVABarrier 9.5 mm OD tubing. Duotight offers superior quality when compared to other push-in fittings. Their double EPDM O-ring design provides a more complete and reliable seal, protecting against leaks even when tubing is bent around tight corners. They are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines!  Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C)

Read more less

Delicious draught beer is a true delight, but the key challenge is ensuring that beer arrives to the consumer with all the freshness and flavor the brewer intended. In an ongoing effort to improve the quality of beer served at retail, the Brewers Association (BA) Draught Beer Quality Committee introduces the updated and revised fourth edition of the Draught Beer Quality Manual. The Draught Beer Quality Manual presents well-researched, detailed information on draught line cleaning, system components and design, pressure and gas balance, proper pouring technique, glassware sanitation, and other valuable advice from the experts. Also included is information on both direct- and long-draw draught systems, important safety tips, and helpful visuals for easy reference. Anyone tasked with performing or overseeing draught line cleaning will appreciate the updated recommendations reflecting current best practices. Whether you are utilizing short-term solutions like jockey boxes and picnic taps, or designing or updating a draught system, this book can help you deliver great beer. The focus on cleaning, maintenance, and proper operation of draught systems will help ensure quality beer, from effervescent German weissbiers to lightly carbonated English-style “cask” ales. Dedication to delivering quality draught beer will enhance the customer's experience with the beer you brew, distribute, and pour. This book is intended for draught system installers, beer wholesalers, retailers, brewers, and anyone with an interest in quality draught beer. Prepared by the Technical Committee of the Brewers Association. The Brewers Association Draught Beer Quality Working Group began focusing on draught beer quality at retail in 2007. Under the guidance of Ken Grossman, Founder of Sierra Nevada Brewing Co. and 2008 Chair of the Brewers Association Technical Committee, the brewing community came together to develop a set of best practices and standards to help brewers, wholesalers, retailers, and draught system installers improve and maintain the quality of available draught beer. The Draught Beer Quality Manual continues to evolve through collaborative efforts within the brewing community. Paperback: 120 pages

Read more less

Draft tower shank assembly for 2.5" diameter tower. Specifications: Shank Length: 2.25" Shank Material: Chrome plated brass Bore Size: 3/16" with 1/4" counter bore Barb Size: 1/4" Flange Material: Chrome plated plastic 

Read more less

12" x 6" brushed stainless steel wall mount drip tray (without drain). Details: Stainless steel door mount drip tray with bold brushed finish. Robust 18 gauge Stainless Steel construction. Three keyholes on backsplash plate for easy mounting. Removal grill for easy cleaning. Finished smooth for safety and appearance with welded corners. Specifications: 304 Stainless Steel Brushed Finish Length: 12" Width: 6" Depth: 3/4" Back-Splash: 2.7" Thickness: 18 gauge No Drain Product Sheet

Read more less

Flare threads make it quick and easy to disconnect and sanitize your air stone. Made from 316 stainless steel, 1/2" diameter, stone is 1" in length.

Read more less

The Still Spirits Turbo 500 reflux condenser works on the principles of ceiling temperatures, where it prevents chemical substance above a certain boiling point being processed. Unlike other reflux condensers on the market, the Turbo 500 works with a focus on the water flow and controlling the temperature of the water flow out. Assuming that the temperature of the water flow is stable, it is able to create a ceiling threshold temperature based on the water flow out.NOTE: The T500 Condenser and Boiler are sold separately.

Read more less

Allows you to connect additional Conical Fermenters to The Grainfather Glycol Chiller. Includes: 2 x Cooling Connection Couplers  2 x 2 m (6.5 ft) insulated hoses 

Read more less

Handy tool for tightening wires.

Read more less

"Y" fitting body, 1/4"NPT (male) x (2) 1/4"NPT (female), no outlet fittings

Read more less

A perfect addition to your pilot distilling T-500 or Grainfather.Make a London Dry style gin with the Gin Botanicals Kit and Botanical Basket. Simply make your spirit wash as normal, put your Botanicals Kit ingredients into the basket and screw the basket on to the Alembic Pot Still dome and condensor or T500 condenser (by removing the saddles) and run your spirit through. You can also use the Botanicals Basket to infuse your spirit with other flavors e.g. citrus or elderflower for your own unique brand of spirit.

Read more less

This 2" long stainless steel shank assembly has a 1/4" bore. The following is included in the assembly: 2" 304 stainless steel shank with 1/4" bore Locking ring Sleeve Coupling nut Lock nut Choice of either a black plastic flange or stainless steel flange

Read more less

Replacement 4" Burner for Bayou Classic burners.   Model: AL10 4" Burner 9" Length No-Rust Cast Aluminum

Read more less

4" 304 stainless steel cooler wall coupling with 3/8" bore. Includes a two rubber washers and two lock nuts. Specifications: Material: Stainless Steel 304Finish: SS PolishedLength: 4"Bore ID:  3/8"Thread Size:  5/8"-14 BSP

Read more less

3/4" female hose thread x 1/2" barb, stainless steel

Read more less

These 2.5 gram sulfur discs are ideally sized for 30 gallon barrels.  Break the disc into smaller parts for use in smaller barrels.  Best when used with a sulfur burner. 10 pack

Read more less

Replacement O-ring for 10" filter housing unit.  Prop 65 Warning: This product contains a chemical known to the State of California to cause cancer, birth defects and other reproductive harm.

Read more less

Specification Brass 45° Flare Fittings SwivelFemale Flare Thread Size: 1/4" FFL x 1/4" FFL

Read more less

Replacement tip for 1/2" auto-siphon

Read more less

Spike Brewing 1.5" TC Ripple Element Specifications: 240 Volt, 5500 Watt Stainless Element Includes 1.5" TC Gasket and Clamp  

Read more less

A compact submersible pump for small cooling projects or building a DYI bucket carboy/keg cleaning system.       Specifications: Maximum flow rate: 1300 GPH Max lift height: 10 ft. Comes with 2 barb fittings - 1/2" & 3/4"  High quality 100W motor runs quiet Stainless steel impeller shaft 6 ft. long power cord For cooling, recommended for batch sizes between 10 gallons to 2 bbl

Read more less

Spike Brewing conicals come equipped with this 100% sanitary sample valve. Taking samples has never been so easy; simply twist the valve handle to slowly draw out a sample from your fermenter for a gravity reading. The one downside is you might end up with lower final volumes due to how easy it is to take taste tests ;)Specifications:  1.5" TC 304SS FDA Silicone seals 3/8” barb

Read more less

Spike Brewing's TC100 temp control system will manage both cooling and heating of your Spike Conical. The digital controller's temp probe will feed into the included thermowell on our CF Series Conical. Also included is a specially fitted neoprene jacket which features reinforced port holes to reduce the chance of ripping during install. Last (and maybe the coolest item) is Spike Brewing's special insulated tubing. This almost eliminates tube cooling losses and will prevent your cooling lines from sweating all over your floor! Cooling:When the temp in the conical rises above the set point it will turn on the pump submerged in your cold water reservoir (bucket of ice water, dorm fridge, aquarium or glycol chiller, DIY AC chiller, etc). This will pump cold water/glycol through the temp control coil, which mounts to the lid, cooling your beer until it reaches the controller set point. Heating:When the temp in the conical falls below the controller set point the optional heater will kick on warming the unit up.  Detailed product guide:Product Guide.pdf TC100 Package:-Digital closed loop controller (heating and cooling)-Insulated tubing (more efficient and no more sweaty tubes!-Temp control coil-Neoprene insulated jacket-Submersible pump (pumping cold water through the temp coil)-Temp Coil Quick Connect Fittings TC100 + Heat Package:-TC100 Package (above)-Optional heater (for us northern brewers)    Limited availability in store.  Drop ships from vendor.

Read more less

CF5 SPIKE CONICAL UNITANK Spike Brewing has completely re-designed their stainless conical line from the ground up. It took a year in the making and are confident that these are the best conical fermenters on the market! Along with the new TC100 Temp Control System, you'll have everything you need to Elevate Your Brew Day! CF5 Features: 304 stainless steel; 1.2mm (18ga) All sanitary welded ports (no-weldless fittings) All hardware shown here is included! Designed for 2.5 to 6 gallon batches 7 gallon total capacity 15 psi working pressure (always use a 15 psi pressure relief valve) Use for pressure transfers Use as a brite tank Etched volume markings 14" wide by 29¨ tall Fully polished finish Lid Features: 4" TC modular top port Allows for hop additions, temp control coil, top sight glass, etc Three 1.5" TC ports which allow for:  Blow Off Port – Dedicated port for an airlock or blow off tubeHop Port – Dedicated port for adding hopsPRV Port – Dedicated port for your pressure relief valve (PRV) Stainless band clamp for attaching the lid Completely removable lid for easy cleaning Body Features: Huge 2" TC bottom dump with butterfly valves (no more stuck yeast dumps) 1.5" TC racking port with butterfly valve 1.5" TC sample valve (for taking gravity readings) 1.5" TC thermowell with 3" dial thermometer  Limited availability in store.  Drop ships from vendor.

Read more less

Water is arguably the most critical and least understood of the foundation elements in brewing beer. Water: A Comprehensive Guide for Brewers, third in Brewers Publications’ Brewing Elements series, takes the mystery out of water’s role in the brewing process. From an overview on sources, quality and geography, the book leads brewers through how to read water reports, understanding flavor contributions, and the treatment and chemistry of brewing water. Authors John Palmer and Colin Kaminski lead a discussion of adjusting water to styles of beer, residual alkalinity, malt acidity, mash pH, brewery process water and wastewater treatment is included. Author: John Palmer and Colin Kaminski Paperback: 300ISBN-10: 0937381993ISBN-13: 978-0937381991Product Dimensions: 6 x 0.8 x 8.8 inches

Read more less

Limited availability in store, drop ships from vendor.   The Grainfather Conical Fermenter Pro gives brewers more flexibility and freedom during fermentation than ever before!   Product Description The Grainfather Conical Fermenter Pro has built-in wireless control, so you can control and monitor fermentation from anywhere!  The Conical Fermenter Pro gives brewers more flexibility and freedom during fermentation than ever before! Connect the built-in wireless controller to the internet and the Grainfather App, add fermentation tracking devices and control/monitor fermentation from anywhere!   The Conical Fermenter Pro allows you to dump yeast, take samples and transfer your wort via our innovative, dual function, valve design. Partner it with the Glycol Chiller*** and get full control over the heating and cooling of your unit. FEATURES: Double Walled: A stainless steel double walled skin is filled with a thick layer of polyurethane foam for insulation. This is what keeps the wort at a constant stable temperature with minimal influence from any external environmental temperature changes, providing insulation for your fermentation that a standard jacket cannot achieve.  Integrated Gentle Heating: In the cavity of the fermenter between the outer body and cone sits a 30 Watt, 12V heating element. Unlike standard heating elements/sources that directly heat the liquid, this heat source is designed to heat the environment in between the walls of the fermenter, which in turn heats the liquid. It is similar to controlling the temperature in a temperature-controlled room. The fermenter acts as an artificial environment that can be heated, meaning the temperature is raised in an even and controlled manner which is much better for the yeast. Integrated Cooling Sleeve: In between the two stainless steel walls sits a cooling sleeve (also made of stainless steel). This cooling sleeve is welded onto the inner wall of the fermenter and can be hooked up to the additionally purchased Glycol Chiller. Temperature is dialed into the Temperature Controller and as the cooling liquid travels through this sleeve, it cools the stainless steel which in turn evenly cools the beer in the fermenter. The cooling sleeve never comes into contact with the beer, it is completely concealed, built into the fermenter, and never needs cleaning or sanitizing - a true innovation for a fermenter of this scale.Easy Access to the Interior for Hassle-Free Cleaning: The Grainfather Conical Fermenter has a smooth interior with no additions such as cooling coils or additional sampling valves meaning it is easy to clean and minimizes the risk of infection. Golden Angle Conical: The conical shape of the fermenter is typical for professional breweries. Our conical has been designed with the 'Golden Angle' of 60º. This is the optimum angle for yeast and sediment to drop down to the bottom of the cone without getting stuck to the sides, allowing you to transfer from above the sediment line, resulting in clearer beer. The conical shape also allows for better mixing during fermentation due to the path of convention currents that it enables to occur. Dual Valve Tap: Make the yeast dumping, transferring and sampling process more professional with this innovative all in one valve. Sampling and transferring is done through an inlet above the sediment line, allowing for clear, sediment-free beer. Easily collect your yeast from below the sediment line with the same unique valve for recultivating and pitching. The innovative design of the valve allows for this dual functionality and less cleaning for you.  Support: The Grainfather Conical Fermenter is fully supported around the world by a fantastic support team who love brewing just as much as you do. Our support team is here for any technical inquiries on brewing or how the Conical Fermenter works, as well as general customer service inquiries. All Grainfather Conical Fermenters come with a 24-month warranty. Includes: Conical Fermenter  Fermenter Lid Rubber Bung Bubbler Airlock Cone Plug Cone Plug Seal 5 cm (2") Tri-Clamp Digital Temperature Display Power Adapter and Wall Plug 2 m (6.5 ft) M12 3-Pin Power Cord Dual Valve Tap Wi-Fi Capable Wireless Temperature Controller Specifications: 304 Stainless Steel Body (polished inner and brushed outer) 30 L (8 US Gal) capacity (volume markings on inner body up to 25 L (7 US Gal) 30 W, 12 V heating power 3.8 cm (1.5") ferrule on lid (for pressure transfer attachments) 5 cm (2") ferrule on bottom of cone Dual Valve Tap with 110 mm (4.3”) inlet Dimensions of Conical Fermenter:  Diameter with handles: 360 mm (14.2") Height (without airlock): 910 mm (35.83") Height with bubbler airlock: 1090 mm (42.92") Dimensions of Carton: 368 mm W x 325 mm L x 905 mm H Limited availability in store, drop ships from vendor.

Read more less

Protect your Taprite brand regulator with this metal guard.  Tanks occasionally tip over and damage the gauges when they do. This guard takes the blow instead of your gauge.   Attaches to the regulator by screwing into the back.  Does not work with the Micromatic or Komos branded regulators.

Read more less

Pressure gauge, 0-160 psi, 1/4" npt bottom inlet, right hand threads.  

Read more less