Products
$10.95
Spike Brewing False Bottom for NPT Kettles
These Spike Brewing false bottoms are for use with their standard Spike kettle line that uses NPT fittings. For the standard Spike+ kettle line that uses TC fittings please see HERE. Design Features: All stainless design; no Silicone gasket to make a seal Low profile design; extremely low dead space (<.25gal) Best filtering on the market due to dual stage filter design; 99.9% grain filtering efficiency Pickup tube and push to connect fitting are included False bottom and pick up tube are Made in the USA! 2 Stage Filtering: Stage 1: Filters through top plate's optimally engineered sized laser cut slits Stage 2: Bottom ring supports the grain weight while also filtering the wort again before it reaches the pickup tube **False bottoms are not designed to filter pellet hops in the boil kettle. Instead you'll want to create a whirlpool to center the hop material and then drain using a side pickup (HERE)**
$126.50 - $253.00
Spike Brewing False Bottom for TC Kettles
These Spike Brewing Spike+ false bottom is for use with their Spike+ line which uses TC fittings. For the standard Spike kettle line that uses NPT fittings please see HERE. Design Features: All stainless design; no Silicone gasket to make a seal Low profile design; extremely low dead space (<.25gal) Best filtering on the market due to dual stage filter design; 99.9% grain filtering efficiency TC Pickup tube, gasket and clamp are included False bottom and pick up tube are Made in the USA! 2 Stage Filtering: Stage 1: Filters through top plate's optimally engineered sized laser cut slits Stage 2: Bottom ring supports the grain weight while also filtering the wort again before it reaches the pickup tube **False bottoms are not designed to filter pellet hops in the boil kettle. Instead you'll want to create a whirlpool to center the hop material and then drain using a side pickup (HERE)**
$135.00 - $250.00
Spike Flow
It's time to go with the (higher) Flow. With features like an Air Relief Valve (ARV), 6-vane impeller design, stainless steel precision machined casting and an integrated impeller shaft and thrust bearing, the Flow is the newest and most badass pump to hit the market. Higher Pressure & Flow-What's more important? Moving your wort quickly or a powerful CIP? The Spike Flow is leading at both. No compromises here. Air Relief Valve-Air in your lines creating headaches? The Flow features an ARV bleed system. Problem solved. Clog Proof Impeller-With the built-in chopping tines on the impeller, you'll never have to stop mid-Brew Day because of a clogged pump head. Quietest on the Market-The Flow is for brewers who prefer listening to their brewing playlist or the game on TV rather than a loud pump. Specs: • Best-in-class 9GPM (gallons/minute) flow rate• Best-in-class 9.5 PSI of pressure • Air Relief Valve (ARV) makes priming easy and convenient• Built in 1/2" drain barb• 6-vane impeller design optimized for performance and durability• 304 stainless steel precision machined casting with maximized inlet and outlet ports• Integrated chopping tines to prevent clogging• Black anodized motor shell and shot-blasted housing• Easy disassembly, cleaning and reassembly• Ultra-quiet, fan enclosed motor: 120v, 60 Hz • 6 foot power cord • 9" length x 5" width x 7" height • Continuous use rated Available in NPT fittings or TC fittings
$275.00 - $302.00
Spike Solo Panel 110V G1 (V1)
This is the first version of the Solo Panel. Included is the Spike Panel (version 1), power cord, element cord, thermometer cable, and NPT thermocouple. From Spike: 10 Gallon Solo System (120V Option) 3 wire, 120V power input Requires NEMA 5-15 outlet (standard 3 prong household plug) Requires 1 x 15 amp breaker (standard household plug) 6 Foot power cord (from electrical panel to outlet) CONTROL PANEL The Solo's control panel is made with professional-grade components – many the same ones from the panels on our Spike System & pro-grade Nano System – and they're built to last. Here’s why you can be confident on brew day when you use our new single vessel system: INDUSTRY STANDARD PARTS Our components are proven to last. And if you run into any issues, the process to change out parts is quick and easy—no sending your panel in and waiting for weeks on end to get it back. INTERNET FREE You aren't tied to the internet, so if you WiFi connection goes down, your brew day doesn't go down with it. INDUSTRIAL SWITCHES Our panels fire up every time. You won’t experience any software glitches or control panel freeze-ups at critical moments.
$500.00 $299.99
Spike Tank Racking Arm
Specifically designed for our Tank Bottom Drain Boil and Solo kettles, this racking arm is the key component to make sure you take only the highest quality wort to your fermenter and leave hops and trub behind in your kettle. The dual 1.5" TC flange allows the pickup tube to attach to the kettle and allows for a 1.5" TC accessory to attach to the arm as well. We use 5/8" tubing which flows up to four times better than our competitors 1/2" size. Tank Racking Arm fits all 5 sizes of the Tank Bottom Drain Kettles Oversized 5/8" diameter 304 stainless tube Indicator pin lets the brewer see which way the tube is pointing when installed and covered in wort Rotatable when installed from the outside Made in the USA **A 1.5" gasket and clamp will need to be purchased separately if you do not already have spares**
$45.00
Spike+ Pickup Tube - Center
The Spike+ center pickup is specially designed to work with the Spike+ line of kettles. The dual 1.5" TC flange allows the pickup tube to attach to the kettle and have a valve or other 1.5" TC accessory attached to the outside. Spike Brewing uses 5/8" tubing which flows up to 4x better than their competitors 1/2" size. Features: Oversized 5/8" diameter 304 stainless tube Sized to pick up from the center of the kettle Made in the USA **A 1.5" gasket and clamp will need to be purchased separately if you do not already have spares**
$40.00 - $45.00
Spike+ Pickup Tube - Shorty
The Spike+ shorty pickup is specially designed to work with Spike Brewing's Spike+ line of kettles. The dual 1.5" TC flange allows the pickup tube to attach to the kettle and have a valve or other 1.5" TC accessory attached to the outside. They use 5/8" tubing which flows up to 4x better than their competitors 1/2" size. Features: One size fits all Spike+ kettles Oversized 5/8" diameter 304 stainless tube Sits on the bottom of the kettle for very low volume losses Made in the USA **A 1.5" gasket and clamp will need to be purchased separately if you do not already have spares**
$34.00
Spike+ Pickup Tube - Side
The Spike+ side pickup is specially designed to work with Spike Brewing's Spike+ line of kettles. The dual 1.5" TC flange allows the pickup tube to attach to the kettle and have a valve or other 1.5" TC accessory attached to the outside. They use 5/8" tubing which flows up to 4x better than their competitors 1/2" size. Recommend Uses: Boil Kettle - Create a whirlpool inside your kettle so hop material collects in the center of the lower stepped section. The side pickup will drain clear wort from the side, above the stepped bottom, avoiding the hop and trub material which has settled. Custom Kettles - Works as a top re-circulation arm or a whirlpool arm. Features: One size fits all Spike+ kettles Oversized 5/8" diameter 304 stainless tube Sized to pick up from above the stepped bottom to avoid hop/trub pickup Rotatable from the outside when installed Made in the USA **A 1.5" gasket and clamp will need to be purchased separately if you do not already have spares**
$34.00
Splash Guard for Cannular Pro Semi-Auto Bench Top Can Seamer
Description The optional splash Guard for the Cannular Pro Semi-Auto Bench Top Can Seamer.
$66.00
Square Cheese Mold
Square mould for feta cheese, brie and or cheddar about 500g or requiring a possible pressing (provide 2 moulds to stack them).
$4.99
Square Cheese Mold - Italian Style
Square form, slotted with bottom for Italian-style fresh cheeses, fresh unpressed cheeses -- especially feta. Form dimensions are 4.25" x 3.75" x 3.5" (top x base x height)
$4.99
Square Cloth Fermenter Cover - 13.7 x 13.7 in.
This 13.7" x 13.7" Square Cloth Fermenter Cover is perfect for Kombucha brewing! Made with breathable fabric, it helps keep your SCOBY healthy without letting in bugs or contaminants. Perfectly sized for larger open top fermenters.
$4.40
Square Cloth Fermenter Cover - 7.8 x 7.8 in.
These square cloths are perfect for Kombucha brewing. Let your fermenting SCOBY breathe while keeping bugs and airborne contaminants out. Perfect for 1 gallon jar fermenters
$2.20
Square Perforated Pizza Peel
The main purpose of a perforated pizza peel is to get rid of excess flour from the pizza base. But why do you want to get rid of the flour? When you’re baking pizza on hot stone or steel, you don’t want flour on the baking surface because it burns. Fine wheat flours that are most commonly used for baking pizza burn at fairly low temperatures. It’s this flour that causes trouble. Dusting your pizza peel with semolina flour, which can handle higher heat better, can also help. Burnt wheat flour will make the oven smoky and will result in more cleaning work when you’re done baking. The burnt flour tends to stick and can be a real pain to get rid of. Especially on an unglazed pizza stone. And if you’re not able to clean the stone properly, the flour can keep smoking next time you use the stone. Less Contact Surface – Less StickingA perforated peel has a smaller surface that is in contact with the pizza dough. This means pizza is less likely to stick to a perforated pizza peel. The reason is that the larger the contact surface is, the more friction there will be between the peel and the pizza. And more friction means it is more likely to stick. A smaller contact surface also means that you’ll need less flour when you’re dusting the peel. As noted above, you want as little flour as possible in the hot oven. So in addition to removing more flour from the dough itself, the peel need less flour due to the holes. Perforated pizza peels are also lighter than solid pizza peels, due to less metal on the carrying surface. This will make it easier to use the peel. Less Condensation – Crispier Pizza CrustWhen you take a hot pizza out of the oven, you may have noticed that water sometimes is formed under the pizza. This moisture makes the pizza less crispy, or even soggy. Using a solid pizza peel may create condensation when the hot pizza meets the cold (room temperature) surface. This is mostly a problem with metal peels since hot air is trapped between the pizza crust and the smooth carrying surface. Condensation happens when this hot air is cooled down to a certain point (it’s dew point), and water drops are created. When you’re using a perforated pizza peel, on the other hand, you will experience less condensation. The reason is that the holes let the hot air escape through the peel. Size Options 12" Square x 31" Long 14" Square x 31" Long Lightweight aluminum construction. Note: Phillips Head screwdriver required for assembly.
$55.00 - $61.00
SS 45 Degree Elbow
1/2" FPT(female pipe thread) stainless steel 45 degree elbow.
$4.65
Ss Infussion Mash Tun Hose Barb - 3/8 in. to Knurled 1/2 in. FPT
3/8" Hose Barb with 1/2" fpt Knurl for SS Brewtech Mashtun 304 stainless steel Fits into SS Brewtech's mash tun bulkhead fitting Needed for MT recirculation manifold
$11.95
Ss Infussion Mash Tun ReCirculation T Barb
SS Brewtech's 1/2" Re-circulation Tee Barb 304 stainless steel 1/2" hose barb 1/2" fpt on mashtun side 1/2" mpt on outer side Hose clamp and silicone tubing not included.
$15.95
SS304 Cooling Coil - 50' x 5/16'' OD
304 Stainless Steel Cooling Coil. Includes grommets, ferrules, and hex nut fittings for easy connection to shanks. Specifications: Material: Stainless Steel 304 Size: 50ft x 5/16" OD (Tube) Diameter: 5.25" (coil) Height: 6.75" (coil)
$99.99
Stainless - 1/8 in FPT x 1/4 in Barb
Stainless 1/8 inch female pipe thread with 1/4 inch barb.
$6.30
Stainless - T.C. Clamp (2.5 in)
Stainless steel 2.5" TC clamp
$11.95
Stainless Ball Valve - 1/2 in Full Port
304 stainless steel, 1/2" full port ball valve. Specifications: 304 Stainless Steel 1/2" FPT No locking clip 1000 psi rating
$18.95
Stainless Beer Thread Adapter | 2 pack | Female Beer Thread x 1/2 in. BSP | KOMOS®
Convert draft shanks or keg couplers for use with 1/2" female threaded fittings. Featuring a hex nut exterior for easy wrench adjustments. The female side is standard beer thread which is used on both ports of standard keg couplers and the tail end of draft shanks. Once installed, you can adapt these input/output ports to any 1/2" fittings and valves you might find useful. The 1/2" male BSP end may require teflon tape if used with 1/2" NPT fittings. Comes in a pack of 2
$11.00
Stainless BSP Washer - 3/8 in.
Stainless steel 3/8" BSP washer.
$3.30
Stainless Bucket Fermenter
If you've been looking to step up from fermenting in plastic buckets or carboys, this is an excellent choice for your next fermenter. Stainless steel is a much better option than glass or plastic, as it is extremely easy to clean and virtually lasts forever. There's also much less chance of contamination as stainless doesn't scratch like plastic. Over time, you'll get scratches in plastic fermenters from normal wear and tear, creating microscopic havens for bacteria. Meanwhile, glass carboys are always at risk of breaking which is something you will never have to worry about with stainless steel. The Bucket Buddy represents a great value for a stainless fermenter in this size. Another advantage over carboys and plastic buckets is the domed base inside the fermenter which is great for yeast flocculation when fermentation is complete. The included racking arm will make it easy to transfer out every last drop of beer while leaving the yeast cake undisturbed. The entire racking arm and ball valve assembly is weldless, which means you can remove the assembly to clean and sanitize it between batches. You can even boil the assembly for added assurance that it's been sterilized. Also available with built-in heating element for fermenting in colder environments. You can also use a heat wrap or heat belt on the outside of this unit. To help maintain a steady temperature, the Bucket Buddy pairs well with either the BrewZilla Neoprene Jacket or the FermZilla Insulating Jacket. For cooling, you can place the fermenter in a dedicated refrigerator or drill into the lid to install a Temp Twister Cooling Coil. A temperature controller probe can then be inserted into the thermowell to control your heating and cooling sources. This unit comes standard with silicone tubing to transfer from the ball valve to your bottles or cans, as well as a stopper and airlock for the domed lid. Specifications: 304 stainless steel construction 9 gallon total capacity Digital thermometer (Temp reads in °C) Weldless thermowell Stainless steel outlet valve with rotating racking arm Stopper & airlock included External Dimensions: 28" H x 15" W (including handles) Internal Dimensions: 22" H x 11.75" W Includes a #3 rubber stopper
$159.99 $150.00
Stainless Bucket Fermenter with Heating - 35L
If you've been looking to step up from fermenting in plastic buckets or carboys, this is an excellent choice for your next fermenter. Stainless steel is a much better option than glass or plastic, as it is extremely easy to clean and virtually lasts forever. There's also much less chance of contamination as stainless doesn't scratch like plastic. Over time, you'll get scratches in plastic fermenters from normal wear and tear, creating microscopic havens for bacteria. Meanwhile, glass carboys are always at risk of breaking which is something you will never have to worry about with stainless steel. The Bucket Buddy represents a great value for a stainless fermenter in this size. Another advantage over carboys and plastic buckets is the domed base inside the fermenter which is great for yeast flocculation when fermentation is complete. The included racking arm will make it easy to transfer out every last drop of beer while leaving the yeast cake undisturbed. The entire racking arm and ball valve assembly is weldless, which means you can remove the assembly to clean and sanitize it between batches. You can even boil the assembly for added assurance that it's been sterilized. This model has an integrated (concealed) 36-watt heating element. No need to worry about accessories such as heating belts and external temperature controllers. This stainless steel fermenter will keep your yeast at optimal temperature making it the ideal option for cold climates. To help maintain a steady temperature, the Bucket Buddy pairs well with either the BrewZilla Neoprene Jacket or the FermZilla Insulating Jacket. For cooling, you can place the fermenter in a dedicated refrigerator or drill into the lid to install a Temp Twister Cooling Coil. A temperature controller probe can then be taped to the side of the fermenter. This unit comes standard with silicone tubing to transfer from the ball valve to your bottles or cans, as well as a stopper and airlock for the domed lid. Specifications: Capacity: 35L Brimful Body Material: 304 Stainless steel Outlet Valve Type: Stainless steel, nylon bushings, silicone seal and stainless rotating rack arm. Thread on tap is 1/2" Lid: 304 Stainless steel Display: Digital temperature display Heating: 36 Watt Concealed Element Stopper & airlock included Temperature reads in °F or °C With elements turned off, hold both +/- buttons to switch between °F or °C External Dimensions: 28" H x 15" W (including handles) Internal Dimensions: 22" H x 11.75" W Includes a #3 rubber stopper
$199.00
Stainless Bucket Fermenter with Heating - 65L/17.1G (110V)
This top value fermenter is made from 304 grade stainless steel and has an integrated (concealed) 60-watt heating element. No need to worry about accessories such as heating belts and external temperature controllers. This stainless steel fermenter will keep your yeast at optimal temperature making it the ideal option for cold climates. The welding is smooth and the outer body has a sleek brushed stainless finish making it easy to clean and maintain. The base inside this unit is a dome so it's really easy to clean while the rotating rack arm enables you to drain out every last drop. This unit comes standard with silicone tubing to transfer from the ball valve to your bottles or cans. Specifications: 110V / 60W power Capacity: 65L Brimful Body Material: 304 Stainless steel Outlet Valve Type: Stainless steel, nylon bushings, silicone seal and stainless rotating rack arm. Thread on tap is 1/2" Lid: 304 Stainless steel Display: Digital temperature display Heating: 60 Watt Concealed Element Stopper & airlock included Temperature reads in °F or °C With elements turned off, hold both +/- buttons to switch between °F or °C Please note: Heating capacity is highly dependent on ambient temperature and use of insulation. The 65L Bucket Buddy is appropriate for warm fermentations such as kveik. Adding insulation may increase heating capacity while colder ambient environments may lower heating capacity. KegLand Part Number: KL23061
$275.00
Stainless Butterfly Hose Clamps | 10 Pack | 1/2 in. to 1 in.
These stainless steel butterfly hose clamps are the ideal choice for connecting silicone tubing to quick disconnects, pumps, and more. The butterfly thumb screw allows for toolless tightening and untightening, so you can build out or break down your system without rummaging through the toolbox for the right screwdriver. Fits 1/2 in. OD to 1 in. OD tubing. Actual size of the clamp is 14-25 mm (0.55-0.98 in.). This 10-pack comes in a convenient zip lock bag.
$11.00
Stainless Carbonation and Line Cleaning Cap
This stainless steel ball lock cap features soda bottle threads, allowing you to convert a soda bottle into a pressurized growler. It is compatible with both gas and liquid ball lock disconnects. Also works well for cleaning draft lines. Simply add line cleaning solution to a soda bottle, attach it to the draft line, and open the faucet to push solution through. This is a direct replacement to ball lock fittings included with the FermZilla pressure kit. It can also be attached to the FermZilla collection container, enabling you to purge the collection container of oxygen. 28mm PCO 1881 Threads
$15.50
Stainless Carbonation and Line Cleaning Cap - Duotight Compatible
This stainless steel ball lock cap features soda bottle threads, allowing you to convert a soda bottle into a pressurized growler. It is compatible with both gas and liquid ball lock disconnects. Also works well for cleaning draft lines. Simply add line cleaning solution to a soda bottle, attach it to the draft line, and open the faucet to push solution through. This is a direct replacement to ball lock fittings included with the FermZilla pressure kit. It can also be attached to the FermZilla collection container, enabling you to purge the collection container of oxygen. 28mm PCO 1881 Threads This version features a 6.5mm Duotight compatible stem. Use the 8mm or 9.5mm reducer to attach EVABarrier draft line.
$15.50
Stainless Funnel w/ Strainer
Features a removable mesh strainer. Use to decant wine or fill narrow bottles with sauces, teas, oils, etc... Stainless steel construction. Measures: 7.5" x 4.75" x 3" / 19cm x 12cm x 7.5cmMouth measures: 3" x 3" / 7.5cm x 7.5cmStem measures: .375"/.95cm wide 3"/7.5cm long
$14.50
Stainless Growler Filler Fitting
Fill your growlers with ease with this stainless fitting and 5/16" ID or 3/8" ID tubing. Faucet insert is 1/2" OD and the barb is 3/8" OD. Fits most standard faucets. Does not fit Intertap, Nukatap, or Perlick
$6.99
Stainless Hop Filter w/ Adjustable Hook - 14 in. x 6 in.
Keep your hops in the kettle and out of the fermenter with this hop filter basket. Conveniently hangs inside the boil kettle and can be removed at any time if needed. The adjustable hook is great for positioning the filter based on the size of your kettle and the volume of wort you're boiling. When fully extended, you can lower the basket an extra 9 inches into the kettle. Also works great as a secondary filter when transferring sweet wort from a mash tun to the kettle. Specifications: Made from 304 stainless steel Adjustable hanging hook 14" H x 6" Ø
$47.50
Stainless Hop Tube
Made from 304 stainless steel, the hop tube is ideal for adding larger amounts of hop pellets, flowers or spices to your large mouth fermenter, boil kettle, or corny keg. The fine mesh will prevent large particles from blocking beverage out dip tubes, pumps, or chillers. It will hold approximately 5 oz of hop pellets, allowing for some space to permit full extraction of the hop oils. It is ideal for dry hopping in the keg and can also be used for fruits, wood chips, spices and more.
$19.00
Stainless Lock Nut - 3/8 in. BSP
Stainless Lock Nut. 1/4 in. female BSP.
$3.10
Stainless Mix-Stir De-Gassing Rod, 22''
Stainless 22" rod with replaceable plastic fins and end cap to protect carboys. Attaches to electric drill.
$32.99
