Search results for "spike solo"
Spike+ Pickup Tube - Side
The Spike+ side pickup is specially designed to work with Spike Brewing's Spike+ line of kettles. The dual 1.5" TC flange allows the pickup tube to attach to the kettle and have a valve or other 1.5" TC accessory attached to the outside. They use 5/8" tubing which flows up to 4x better than their competitors 1/2" size. Recommend Uses: Boil Kettle - Create a whirlpool inside your kettle so hop material collects in the center of the lower stepped section. The side pickup will drain clear wort from the side, above the stepped bottom, avoiding the hop and trub material which has settled. Custom Kettles - Works as a top re-circulation arm or a whirlpool arm. Features: One size fits all Spike+ kettles Oversized 5/8" diameter 304 stainless tube Sized to pick up from above the stepped bottom to avoid hop/trub pickup Rotatable from the outside when installed Made in the USA **A 1.5" gasket and clamp will need to be purchased separately if you do not already have spares**
$34.00
Spike+ Pickup Tube - Center
The Spike+ center pickup is specially designed to work with the Spike+ line of kettles. The dual 1.5" TC flange allows the pickup tube to attach to the kettle and have a valve or other 1.5" TC accessory attached to the outside. Spike Brewing uses 5/8" tubing which flows up to 4x better than their competitors 1/2" size. Features: Oversized 5/8" diameter 304 stainless tube Sized to pick up from the center of the kettle Made in the USA **A 1.5" gasket and clamp will need to be purchased separately if you do not already have spares**
$40.00 - $45.00
15 Gallon Spike+ Kettle
15 GALLON SPIKE+ BREW KETTLE Introducing Spike Brewing's new Spike+ line of kettles! Spike+ is just that, an improvement on an already great platform. The Spike+ line draws from the pro side of brewing with the standard use of tri-clamp (TC) fittings. TC fittings do not have any threads and use a gasket and clamp which allows for quick attaching/detaching of fittings. The Spike+ line is for the most serious homebrewers! While designing the setup of the kettle, Spike Brewing offset the ports on these kettles, so you have ample room to use our butterfly valves, or other accessories, with ease. Kettle Features: 5 – 11 gallon batch 304 (18/8) stainless steel Sanitary welded coupler design (done at Spike Brewing's facility in Milwaukee, WI) 1.2mm thick walls (thickest on the market) 5mm tri-clad bottom (induction capable) Internal volume markings Polished finish 15.8¨ wide by 19.4¨ tall Domed bottom design Bottom coupler 2" off the bottom (2 gallon mark) Top coupler 4" off the bottom (3 gallon mark) Staggered design keeps the top port submerged with half batches Lid is included Pictured Ball Valve and Thermometer Sold Separately. Limited availability in store. Drop ships from vendor.
$350.00
Conical Replacement Lid Gasket
The Spike Brewing conical lid gasket is a one piece design made from FDA approved Silicone. This design allows for an easy install and easy clean up. Simply push the gasket into the gasket groove on the lid. Specifications: Black in color FDA approved Silicone
$13.00 - $40.00
Racking Arm
Another cool product the Spike Brewing engineers and in-house welders developed is their USA made racking arm. This racking arm provides 6" of total travel allowing you to draw clear wort even with the hoppiest of beers.The racking arm also incorporates a position indicator that is welded on so the orientation of the racking arm can easily be seen from the outside of the sealed conical (especially useful in closed pressure transfers). Specifications: 1.5" TC 304SS Position indicator Works with every size conical Made in the USA **A 1.5" gasket and clamp will need to be purchased separately if you do not already have spares**
$40.00
Conical Unitank Bracing Shelf
Spike Brewing's custom bracing shelf is made in the USA and is a recommended addition when casters or leg extensions are installed for additional stability. Their bracing shelf will also come in handy as a storage shelf for blowoff buckets, tools and more. Specifications: 304SS Super thick 14ga material Made in the USA Bracing shelf install and instructions:Install + instructions
$45.00 - $50.00
CIP Ball
Another cool innovation from the Spike Brewing engineers; their low pressure CIP ball! They wanted to design a CIP ball that didn’t require home brewers to purchase another pump if they already owned one. Small brewery pumps, like Chugger and March pumps used on our Spike System, are very common for most home brewers. However, most CIP balls require a much larger pump to work properly. This CIP ball was specifically designed to work with the more common 7GPM pumps. It has also been tested with larger sump pumps which are also commonly used for CIP applications. Spike Brewing also designed the CIP ball to fit through a 1.5" TC port. This allows for quick install of the CIP ball after fermentation. This works especially well with cleaning the temp control coil. They recommend a 5-10min CIP with 160F brewery wash to give a nice and shiny FLEX or conical fermenter. Pro Tip:If you do not have a FLEX+ lid with 1.5" TC port you can attach the CIP ball to the secondary port of your FLEX after an initial dump and rinse. Then simply CIP as described above! Specifications: 1.5" TC x 1.5" TC 304SS Low flow design
$70.00
FLEX Replacement Lid Gasket
The Spike Brewing conical lid gasket is a one piece design made from FDA approved Silicone. This design allows for an easy install and easy clean up. Simply push the gasket into the gasket groove on the lid. Specifications: Black in color FDA approved Silicone Works with the FLEX and FLEX+
$12.00
Gas Post x 1/4" NPT
Since most brewers who keg use ball lock connections for hooking up their CO2 tank we figured why not design a ball lock fitting to easily add CO2 to your conical! The Spike Brewing gas post assembly has a standard ball lock gas post on one end with a 1/4" NPT on the other. This allows it to screw directly into Spike Brewing carb stone as well as the their gas manifold. Specifications: Stainless steel Ball lock x 1/4" NPT Comes with replacement o-ring
$11.00
Caster Kits
The Spike Brewing casters screw directly into the bottom of their conical legs for easy installation. The CF5, 10 and 15 use a 3" caster while the CF30 uses a larger 4" caster. CF5, CF10, CF15 Specifications: 3" caster wheel Set of 3 Non-marking wheel Locking brake + locking swivel CF30 Specifications: 4" caster wheel Set of 4 Non-marking wheel Locking brake + locking swivel *Spike Brewing recommends a standard or extended bracing shelf when using the casters for added stability* Caster wheel install and instructions:Install + instructions
$40.00 - $63.00
Leg Extension Set
**Not for use with the CF30** The shorty leg extensions are 9” long (compared to 18”). They were specifically designed to be used with the 2” sight glass in the vertical arrangement. This was the major design criteria that Spike Brewing engineering noticed.The long leg extensions were specifically designed to bring the racking port to a height where the conical can be gravity drained into a 5 gallon corny keg. However they are pretty long for those people that do not need to gravity transfer but want the conical high to use a sight glass for example. *It is recommend to use the standard or extended bracing shelf when using the leg extensions for added stability* Shortly leg extension specifications: 304SS 9" long Top threads for attaching to conical legs Bottom threads for attaching leveling feet and casters Long leg extension specifications: 304SS 18" long Top threads for attaching to conical legs Bottom threads for attaching leveling feet and casters
$45.00 - $60.00
TC Sample Valve Gasket Set
FDA approved EPDM gaskets for all your sample needs. Go get yourself a new gasket and seal that baby right up!
$2.50
2'' 90° TC Elbow
This is the same elbow featured on the bottom of the Spike Brewing conical line. Specifications: 2" TC 304SS
$21.00
