Draft Supplies

Plastic snap clamp for 3/8" I.D. vinyl draft hose.

Read more less

Stepless Oetiker Clamp, Size 17.0mm

Read more less

Stainless steel shank assembly with black plastic flange.  A great option for dispensing beer, wine, cider, or kombucha.   Specifications Length: 4-1/8" Bore I.D.: 1/4" Thread: 7/8"-14 (5/8" BSP) Material: 304 stainless steel shank

Read more less

Made from 304 stainless steel, set of 2, for the front and back of your gauges. These cages will protect your regulator gauges from damage. Works with Micro Matic and NADS regulator.

Read more less

Chrome plated beer shank assembly Specifications: Chrome plated brass shank 5 1/8" length 1/4" bore plastic flange Does not include hose tailpiece Important information – Prop. 65 for CA residents.Proposition 65 Warning: This product contains chemicals known to the State of California to cause cancer and/or birth defects or other reproductive harm.

Read more less

Replacement pressure relief valve rated to blow at 35 psi. This is a direct replacement of the PRV featured on the FermZilla and Kegmenter. It is also compatible with homebrew kegs and the KOMOS® CO2 regulator if you desire a lower blowoff pressure.

Read more less

304 Stainless steel ball lock liquid (beverage out) side connector with 1/4" barb connection.

Read more less

This manifold allows you to serve four beers at the same pressure. It’s made from brass and features a pressure relief valve, shut offs with check valves, 3/8” inlet and outlet barbs, and a 304 stainless mounting bracket.

Read more less

Mini Design - Ideal Flow Rate for Small SystemsMost conventional beer taps are designed with 10mm diameter nozzle/spout so you can pour a pint in just over 10 seconds. This type of flow rate is great for high turnover bars and commercial venues but this high flow rate requirement is not necessary or desirable for all applications.  For compact portable systems, or for home brew draft systems a slower flow rate is easier to control the flow and further reduces foaming issues due to the low liquid volume stored in the tap body.  This NukaTap mini is also more ideal for pouring smaller doses. For example cocktails where 5-8 oz of liquid is dispensed is difficult to control with a high flow rate tap. For portable systems, the NukaTap Mini with the Flow Control Ball Lock QD & Duotight Adapter assembly is small enough to literally put in your pocket, making it ideal for mini keg setups that you want to be portable or that you want to easily fit inside a domestic fridge where space is tight. Forward SealingForward sealing taps are absolutely the way to go when it comes to beer taps. Old legacy taps still exist in the industry that are simply poorly designed. The issue with rear sealing taps is that beer dries up on the tap piston. This is not sanitary and as more and more beer dries up in these components the tap can almost glue completely shut causing damaged seals or broken handles (this is particularly the case if it's left for some time to dry out with beer inside).  These older legacy designs still exist probably due to poor education. The forward sealing designs do not have this problem and the tap drains out completely with no beer drying up on the mechanical moving parts in the same way. This makes the tap more sanitary and reduces maintenance. In many instances the price is similar so there is no reason to use a poorly designed rear sealing tap. All NukaTap faucets are forward sealing. Laminar FlowJust like the NukaTap SS and NukaTap FC, the NukaTap Mini has been designed with laminar flow in mind. Laminar flow is critical for a beer tap as it means you will pour the beer with minimal foaming and a substantial reduction in wastage. Think about how many times a beer tap opens and closes in its lifetime. 1,000 or maybe 10,000 times?  Laminar flow saves wasted beer in excessive foam and the better laminar flow easily pays for itself in a reduction in lost beer. To use poorer designed taps is literally like flushing money down the sink. Extensive modeling has been done on the NukaTap design to improve laminar flow. Integrated Seals That Are Indestructible and More SanitaryUnlike other designs the NukaTap Mini body is made from POK making it strong, robust and able to be autoclaved. The seals are also over-molded from Santoprene® making them hard wearing so they will literally last for the lifetime of the tap without the need for replacement. Santoprene® and POK both have excellent resistance to chemicals such as caustic soda, peroxide, phosphoric acid, lactic acid, citric acid, acetic acid, and all common chemicals sold and used in the beverage industry. The seals internally are over-molded meaning no fissures or cracks exist for bacteria, crud or yeast to hide. Superior First Pour Foam Due to Low Thermal Mass and ConductivityFirst pour foam is an issue caused by a warm tap body. For most taps to pour well it's important to dispense enough beer to cool the tap body down before the tap will pour well.  In addition to this the conductivity of the tab body also makes this worse so insulative materials simply work better than conductive materials. The NukaTap mini not only has very low thermal mass but is also highly insulative being made mostly from Santoprene® and POK. The combination of these two factors in conjunction with superior laminar flow makes for the lowest "first pour foam" effect out of any tap ever produced. Long Shank AlternativeMost conventional beer taps require a large 3/4" hole to be drilled through the wall of your refrigerator, keezer, or wall. Traditional long shanks also generally have a large volume of liquid that sits inside the wall unrefrigerated which is not ideal. This new long shank alternative is designed to suit any wall thickness and greatly reduces the stagnant beer sitting in the shank itself. For walls up to 2.7" thick, these wall mount shank kits include three screws, however if the wall is thicker, you can also use 6 small wood screws or something similar and attach three screws from the front and 3 from the back allowing you to go into any wall type. Another advantage of this new design is the tap will never accidentally rotate. Typically, other long shank beer taps rely on the hex nut on the shank to be done up tight enough to prevent rotation but if the wall compresses (often the case with foam walls) the tap is allowed to rotate. This new design has three fixing points making it impossible for the tap to rotate accidentally as the interlocking teeth behind the collet allow you to set the angle and then do up the collet to fix the tap permanently in that position.

Read more less

This FLOJET in-line water pressure regulator with built-in check valve reduces inlet water pressure to a safe level for use with all Glass Rinser Trays. Specifications: Pressure Regulator comes complete with removable, cleanable inlet screen. Unit is pre—set from factory at 15 PSI.  NSF stardard-18 garden hose x garden hose with 1/2 npt adaptors and 3/8" hose barbs. Kit Model: 01750352C

Read more less

Attach this fitting to convert your Intertap faucet to a ball lock quick disconnector.

Read more less

Sanke Coupler Check Ball Coupler Probe Type: Type A, Type G, Type U

Read more less

Convert a commercial sanke keg to be used with ball lock fittings. To install, remove the keg spear, place the gasket on the keg ferrule with the beaded side facing up, attach the silicone dip tube and place the tapping head on the ferrule, then secure with the 2" tri-clamp. **Be sure to always depressurize the keg before removing the tapping head.** Includes: Ball Lock Post Lid 2" tri-clamp Single-side beaded tri-clamp gasket 60 cm silicone dip tube (23.6") Red 2.5 bar PRV (36 psi)

Read more less

This Duotight to Male Elbow fitting can be used to route tubing connecting to 8 mm Duotight Ball Lock QDs. This is a great way to keep tubing organized and out of the way in your kegerator. Compatible with EVABarrier 8 mm OD Tubing. Duotight offers superior quality when compared to other push-in fittings. Their double EPDM O-ring design provides a more complete and reliable seal, protecting against leaks even when tubing is bent around tight corners. They are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines! Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C)  Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals.

Read more less

Rubber grommet for chrome plated brass ferrule with 1/4" ID bore.

Read more less

This Duotight plug is used to block up your 8 mm (5/16") tees, elbows or other fittings for gas leak testing or simply to plug an unused section. Features: Insert plug and firmly push to connect Release plug by pushing in the collet on the Duotight fitting Suitable for both gas & beverage applications Made from food-grade acetal plastic Temperature rated to 212°F (100°C)

Read more less

This Duotight to 3/4" female thread fitting can be used to connect beverage or gas line to any fitting with 3/4" MPT. Compatible with EVABarrier 9.5 mm OD Tubing (D1719). Duotight offers superior quality when compared to other push-in fittings. Their double EPDM O-ring design provides a more complete and reliable seal, protecting against leaks even when tubing is bent around tight corners. They are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines! Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C)

Read more less

Flush and fill your bottles with ease. The valve has three positions: off, beer, and gas. Insert filler into the bottle in the off position, switch to gas to flush the bottle with CO2, and then switch to beer to fill your bottle. You can control the speed of your flow with the adjustable pressure relief. This filler is designed for use with 12 oz. bottles but can be used with larger formats by attaching a small piece of 1/4" tubing to the filler.

Read more less

Regulator inlet flare fitting for primary regulators. 1/4" NPT (Right Hand Thread) x 1/4" flare Does not include check valve

Read more less

This adapter can be installed on the Core 360 Mini Regulator from Kegland in order to use 74 gram CO2 cartridges. Use a crescent wrench to remove the stock adapter piece for 12 gram cartridges and simply screw in this adapter with 5/8-18 UNF female threading. Switching to 74 g cartridges will allow you dispense 1-4 Cornelius kegs, depending on how it is used and the CO2 consumption required. TR21-4 Male Thread x 5/8-18 UNF Female Thread Adapter only. Regulator and CO2 cartrdige sold separately. KegLand Part Number: KL20411  

Read more less

Beer line 1/4" x 3/8" stainless steel barbed splicer. Splices 3/16" I.D. Vinyl to 5/16" I.D. Vinyl 3/16" I.D. Vinyl to 3/8" I.D. Poly 1/4" I.D. Poly to 3/8" I.D. Poly Specifications Type:  Straight Connectors Material:  304 Stainless Steel I.D.: 3/16"

Read more less

Vinyl beer line 1/2" x 1/2" stainless steel barbed splicer. Splices 1/2" I.D. Vinyl to 1/2" I.D. Vinyl Specifications Type:  Straight Connectors Material:  304 Stainless Steel O.D.: 7/16" I.D.: 1/2"

Read more less

CO2 Bulk Head Length : 4” Long x 7/16″ 1/4" MFL Thread • This bulkhead allows you to keep your CO2 outside of the refrigerator or freezer and run your gas line through the wall without drill a large whole. The rubber gaskets included seal of the whole or the gas and gives.

Read more less

Flanged lock nut for beer shanks, 1-3/16" hex, 29/32-14 thread.

Read more less

Stainless steel gauge cage for KOMOS CO2 dual gauge regulators.  Includes mounting screws. Pictured regulator not included.  

Read more less

Hex nipple, 1/4" NPT, 9/16" hex, 1.87" overall length, for primary regulators, left hand threads

Read more less

Draft tower shank assembly for 2.5" diameter tower. Specifications: Shank Length: 2.25" Shank Material: Chrome plated brass Bore Size: 3/16" with 1/4" counter bore Barb Size: 1/4" Flange Material: Chrome plated plastic 

Read more less

4" 304 stainless steel cooler wall coupling with 3/8" bore. Includes a two rubber washers and two lock nuts. Specifications: Material: Stainless Steel 304Finish: SS PolishedLength: 4"Bore ID:  3/8"Thread Size:  5/8"-14 BSP

Read more less

Protect your Taprite brand regulator with this metal guard.  Tanks occasionally tip over and damage the gauges when they do. This guard takes the blow instead of your gauge.   Attaches to the regulator by screwing into the back.  Does not work with the Micromatic or Komos branded regulators.

Read more less

The humble plastic ball lock disconnect has been around a long time and is used by countless homebrewers around the world.  Despite the extensive use they have seen little to no innovation for decades and KegLand wanted to change this. Enter the Duotight Ball Lock QD. The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably with no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitizing an absolute breeze! Made from highly chemical resistant materials with stainless springs and ball bearings (no cheap ABS plastics here) this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitizers and caustics. The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required This particular ball lock disconnect has been designed for use with EVABarrier 6.35 mm OD Tubing. Due to the integrated Duotight fitting the line will simply push directly into this fitting. Ball Lock Quick Disconnect - Gas In Direct connect 6.3 mm OD EVABarrier tubing Compact design won't interfere with keg stacking Made from highly chemical resistant materials Disassemble by hand for quick and easy cleaning Duotight Ball Lock QDs are offered in three sizes that correspond to the outer diameters seen on our line of EVABarrier Draft Tubing.  6.35 mm OD – features a very tight 3 mm ID that requires only 3.2 ft of length for adequate flow resistance. This is the ideal size for mobile draft or if you want to keep your kegerator as tidy as possible. 8 mm OD – the most common OD size of EVABarrier tubing. This size comes in two IDs (4 mm & 5 mm) and pairs up with the lion's share of Duotight fittings and accessories. 4 mm ID is our most recommended size for beverage lines, requiring 5-6 ft. lengths. 5 mm ID is commonly used as gas line or when 10-12 ft. beverage lines are required. 9.5 mm OD – suitable for gas lines or long draw beverage lines. At 6.3 mm ID, this size is ideal for beverage lines that will be 20 ft. or longer in length.

Read more less

"Y" fitting body, 1/4"NPT (male) x (2) 1/4"NPT (female), no outlet fittings

Read more less

Pressure gauge, 0-160 psi, 1/4" npt bottom inlet, right hand threads.  

Read more less

Replacement jet disc for stout faucet spout. TapRite part SF2003-14 Stout Faucet Diagram

Read more less

Replacement O-rings for Intertap Flow Control faucets.

Read more less