Draft Supplies
CO2 Cylinder Exchange
Does not ship. In store pick up only. Swap out your empty CO2 cylinder with a full one. Tanks will be swapped with the same material as brought in. Tanks must be aluminum and certification no older than 5 years. Cylinders that are out of compliance will not be accepted.
$26.00 - $47.00
3/16" ID Vinyl Draft Tubing
3/16" ID vinyl beverage and gas tubing. Accuflex Bevlex 200 PVC Tubing is used for draft beer transfer and BIB soft drink applications. Its special dual durometer construction combines a low extraction inner contact surface with a flexible outer layer to provide excellent kink resistance and taste protection. NSF-51 Listed. Inside Diameter (ID): 3/16" Outside Diameter (OD): 7/16" Clamp Size: 13.3mm Available in clear or black, by the foot or 100' roll. Prop 65 Warning: This product contains phthalates (DEHP, DBP, BBP), a chemical known to the State of California to cause cancer, birth defects and other reproductive harm.
$1.20 - $79.99
Hose Gear Clamp - Fits 1/4'' to 5/8'' OD Tubing
Stainless steel hose clamp for 1/4" to 5/8" OD tubing. Commonly used with 3/16" ID and 5/16" ID draft tubing.
$1.75
5/16" ID Vinyl Draft Line Tubing
5/16" ID red or clear vinyl beverage and gas tubing. The red color is generally used for gas line. Accuflex Bevlex 200 PVC Tubing is used for draft beer transfer and BIB soft drink applications. Its special dual durometer construction combines a low extraction inner contact surface with a flexible outer layer to provide excellent kink resistance and taste protection. NSF-51 Listed. Inside Diameter (ID): 5/16" Outside Diameter (OD): 9/16" Clamp Size: 15.7mm or 17mm Prop 65 Warning: This product contains phthalates (DEHP, DBP, BBP), a chemical known to the State of California to cause cancer, birth defects and other reproductive harm.
$1.20 - $98.00
Hex Nut Washer
Flat neoprene washer for use with beer shanks or Sanke couplers. Pairs up with a tailpiece and hex nut (or wing nut).
$0.85 - $6.49
Ball Lock Disconnect (Liquid) - 1/4'' MFL
This Ball Lock Disconnect (Liquid) by CM Becker provides a secure liquid flow with a durable plastic coupler and 1/4" MFL male flare thread. Its reliable seal and robust construction make it an ideal choice for Cornelius kegs.
$7.29
Ball Lock Disconnect (Gas) - 1/4'' MFL
CM Becker plastic ball lock gas in coupler with 1/4" MFL. Quick disconnect for ball lock Cornelius (Corny)-type kegs.The 1/4 inch male flare (MFL) threaded fittings make it easy to connect a variety of hardware pieces and connectors. MFL fittings are more versatile than barbed fitting, but they must be tightened down properly or they can leak. Barbed fittings are also available.
$7.29
Flare Swivel Nut & 5/16" Swivel Stem
Swivel nut and stem set. Used to attach 5/16" ID draft or CO2 line to corny keg disconnects. Barb Specifications: Material: Stainless Steel Size: 5/16" Nut Specifications: Material: Brass Finish: Chrome Plated Brass Size: 1/4"
$2.99
5lb Co2 Aluminum Cylinder - Filled
Does not ship. In store pick up only. Filled 5 pound aluminum CO2 cylinder. Will dispense approximately 9 five gallon kegs before needing to be refilled. Dimensions: 18" Tall x 5.25" wide. These are used cylinders that have been filled from a local vendor.
$114.00
Hex Nut for Tailpiece
Nickel Plated Brass Hex Nut, 1" (Beer Thread, 29/32-14). Used to connect a tailpiece to a sanke coupler or a shank. You may also need a tailpiece or hex nut washer. California Proposition 65 Warning: This product may contain a chemical known to the State of California to cause cancer, or birth defects, or other reproductive harm.
$1.95
Flare Swivel Nut with 1/4'' Stem
Swivel nut and stem set. Used to attach 3/16" ID or 1/4" ID draft line to corny keg disconnects. Barb Specifications: Material: Stainless Steel Size: 1/4" Nut Specifications: Material: Brass Finish: Chrome Plated Brass Size: 1/4"
$2.99
Micro Matic American "D" System Keg Coupler
The "D" system keg coupler, also known as American Sankey, is the most common system available in the USA. It is used by all the major North American breweries as well as most craft breweries. The keg coupler connects to the keg valve, "tapping" the keg. Both the gas line from the CO2 tank/regulator and the beer hose to the beer faucet attach to the coupler. Features Chrome plated brass body Tin-nickel plated probe Short handle is ideal for the smaller diameter 1/6 kegs Specifications System: "D" (American Sankey) Body Material: Chrome plated brass Probe Material: Tin-nickel alloy plated Handle Style: Lever Gas Port: 3/8" O.D. Barb (To fit 5/16" I.D. Gas Hose) Beer Port: 7/8"-14 Thread (U.S. Beer Industry Standard) Height: 3-13/16" Manufacturer: Micro Matic ⚠️WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. www.P65Warnings.ca.gov
$36.99
O-Ring Kit for Corny Kegs
Includes O rings for dip tubes, posts, and lid.
$4.50
Beer Line Assembly - Ball Lock to Hand Held Faucet
Beer line assembly for your corny keg hook up. We build the assembly, you just need to secure the the ball lock disconnect to your corny keg. For outdoor dispensing we recommend selecting the black vinyl tubing. This assembly includes: 5' of 3/16"" ID vinyl draft tubing CMB Liquid ball lock disconnect with 1/4" flare fitting 1/4" swivel nut with 1/4" stainless steel hose barb stem 13.3 stepless hose clamp Plastic hand held faucet
$21.99
Ball Lock Disconnect (Liquid) - 1/4'' Barb
Liquid coupler for cornelius keg with 1/4 barb.
$7.29
Hand Held Faucet
Black plastic handheld faucet with a barb for 3/16” or 1/4” ID tubing. Also known as a cobra tap or picnic tap.
$4.49
Duotight 8 mm (5/16 in.) x 1/4 in. Flare
This Duotight fitting with 1/4" Flare is perfect for flared gas and beverage ball lock and pin lock disconnects. This Duotight fitting is compatible with EVABarrier 8 mm OD Tubing. Duotight offers superior quality when compared to other push-in fittings. Their double EPDM O-ring design provides a more complete and reliable seal, protecting against leaks even when tubing is bent around tight corners. They are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines! Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Note: Ball lock fitting and regulator not included.
$4.80
Ball Lock Disconnect (Gas) - 3/8'' Barb
This Ball Lock Disconnect (Gas) connector is the perfect solution for cornelius kegs. Made by CM Becker plastic, this 3/8'' barbed connector is designed for a long-lasting and reliable connection.
$8.29
Keg Lube
Keg lube is a food grade lubricant for rubber and plastic parts. Using keg lube will extend the life of the o-rings on your kegs preventing cracks from developing and leaks from occurring. 1 ounce tube.
$4.50
13.3mm Stepless Hose Clamp - For 3/16" ID Vinyl or 3/8" ID Poly
13.3mm Stainless Steel, Stepless Oetiker Clamp This style of clamp tightens in an exact circle, making them ideal for use with draft lines. For 3/16" ID Vinyl or 3/8" ID Poly Hose Stepless Clamp Tool sold separately.
$0.75 - $12.99
Universal Poppet
Universal poppet valve fits most kegs.
$3.99
Ball Lock Gas Line Assembly
Gas line assembly for your corny keg hook up. We build the assembly, you just need to secure the open end of the tubing to the 5/16" barb on your regulator with the gear hose clamp and the ball lock disconnect to your corny keg. This assembly includes: 4' of 5/16" ID red vinyl tubing Gas ball lock disconnect with 1/4" flare fitting 1/4" swivel nut with 5/16" stainless steel hose barb stem 15.7 stepless hose clamp Stainless steel gear hose clamp
$17.99
Multi Draft Tool with Duotight Remover
The KOMOS multi draft tool is a handy and inexpensive tool that every homebrew kegger should have in their toolbox. It's really useful for the most common fittings that you are likely to see in a home draft system, and Duotight users will appreciate the handy removal tool for 8 mm and 9.5 mm fittings. Functions: CO2 Regulator Nut Spanner Shank Hex Nut Spanner Faucet Coupling Ring Pin Wrench Flare Swivel Nut Spanner 8 mm Duotight Removal 9.5 mm Duotight Removal Bottle Opener
$5.50
3/16" Stainless Steel Tailpiece (304)
3/16" ID stainless steel tailpiece commonly used for 3/16" ID draft tubing. 304 Stainless Steel
$3.49
EVABarrier Double Wall Draft Tubing - 4 mm ID x 8 mm OD
EVABarrier double wall tubing is an excellent choice for all draft dispensing applications. The inner barrier is an excellent gas barrier, keeping oxygen out and CO2 in. The inner wall is also extremely smooth to prevent bacteria and other microbes from attaching to the inside surface. The outer barrier gives the tubing a decent stiffness while still remaining pliable. This makes EVA Barrier remarkably kink resistant and the perfect choice for use with Duotight, John Guest, and other push-in fittings. The 4 mm (5/32") ID size is perfect for home draft applications where only a short beverage line is needed. It is recommended to use 5-6 ft. per line for adequate flow resistance. Specifications: Inner Diameter - 4 mm (5/32") Outer Diameter - 8 mm (5/16") PVC, BPA , and Plasticizer Free* Outer wall prevents oxidation and CO2 loss Smooth inner wall prevents microbial growth build-up *EVABarrier does not contain plasticizers, or phthalates, that are used to make PVC flexible. These plasticizers are known to leach out into the beer over time and have adverse health effects.
$8.00 - $52.50
Black Faucet Handle
Black plastic tap handle for kegerator faucets.
$4.49
Faucet Spanner Wrench - Red Handle
A faucet spanner wrench is a must have tool for all kegerator owners. This wrench with the red coated handle is gentler on the hands when using.
$8.00
15.7mm Stepless Hose Clamp - For 5/16" ID Vinyl
15.7mm Stainless Steel, Stepless Oetiker Clamp This style of clamp tightens in an exact circle, making them ideal for use with draft lines. For 5/16" ID Vinyl Tubing Stepless Clamp Tool sold separately.
$0.75 - $12.99
Faucet Body Coupling Gasket
Faucet body gasket Replacement gasket that seals between a draft faucet and shank.
$1.25 - $9.50
Intertap Stainless Steel Faucet
In normal rear-sealing faucets the entire faucet has to drain of beer. Intertap faucets are forward-sealing which keeps beer in it so the inside doesn't have a chance to get sticky, making cleaning much easier. It also reduces the chance of off flavors transfering to your beer while you pour.Other 'perl' forward sealing faucets use a floating o-ring, which is just as sanitary but requires the o-ring to move inside the faucet body in order to seal correctly. This can become a problem as the faucet ages. Intertap faucets use a sliding shuttle that guides the o-ring into the perfect position every time. The threaded spout easily unscrews from the faucet and can be replaced by a growler filler or stout spout quickly and easily. Pour a pint and then fill a growler in no time at all.304 Stainless Steel construction.
$40.00
Plastic Carbonation and Line Cleaning Cap
This plastic ball lock cap features soda bottle threads, allowing you to convert a soda bottle into a pressurized growler. It is compatible with both gas and liquid ball lock disconnects. Also works well for cleaning draft lines. Simply add line cleaning solution to a soda bottle, attach it to the draft line, and open the faucet to push solution through. When using two ball lock caps, it is recommend pairing this yellow plastic cap with a red plastic cap so you can easily identify which caps are being used for liquid or gas. This cap can also be attached to the FermZilla collection container, enabling you to purge the collection container of oxygen. Specifications: Liquid and Gas Ball Lock Compatible Overall Length - 2.5" Barb Length - 7/8" Barb OD - 1/4" Barb ID - 3/16" 28 mm PCO 1881 Threads
$8.80
O-Ring - Keg Post
Replacement o-ring for Cornelius keg post.
$0.50
Intertap Self Closing Faucet Spring
Turns an Intertap or Nukatap faucet into a self closing faucet by forcing it to the closed position when you let go of the handle. Made from 304 stainless steel. Faucet not included. This spring is not compatible with the Nukatap flow control faucet or other brands of faucets. For the Nukatap flow control spring, click here
$3.00
Micro Matic "D" Style Sankey Coupler, SS304
Micro Matic 304 stainless steel, Sankey D probe coupler for American kegs. Good for dispensing beer, wine, and cider. "D" system is the most common system available in the U.S., also known as American Sankey. It is used by all the major breweries Anheuser-Busch, Miller, Molson-Coors, and Labatt as well as most craft breweries. The keg coupler connects to the keg valve, "tapping" the keg. Both the gas line from the CO2 tank/regulator and the beer hose to the beer faucet attach to the coupler. Specifications: 304 stainless steel body improves durability and resistance to chemicals 304 stainless Steel probe for the ultimate in purity Excellent for beer, wine, and cider 304 stainless steel handle fork for added strength Short handle is ideal for the smaller diameter 1/6 kegs NSF approved Made in the USA
$57.99
Keg Coupler Check Valve
Concave check valve for sanke style keg couplers. This check valve helps to prevent liquid from backing into the Co2 line.
$2.60
Duotight Ball Lock Quick Disconnect (8mm) - Gas In
The humble plastic ball lock disconnect has been around a long time and is used by countless homebrewers around the world. Despite the extensive use they have seen little to no innovation for decades and KegLand wanted to change this. Enter the Duotight Ball Lock QD. The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably with no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitizing an absolute breeze! Made from highly chemical resistant materials with stainless springs and ball bearings (no cheap ABS plastics here) this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitizers and caustics. The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required This particular ball lock disconnect has been designed for use with EVABarrier 8 mm OD Tubing. Due to the integrated Duotight fitting the line will simply push directly into this fitting. Ball Lock Quick Disconnect - Gas In Direct connect 8 mm OD EVABarrier tubing Compact design won't interfere with keg stacking Made from highly chemical resistant materials Disassemble by hand for quick and easy cleaning Duotight Ball Lock QDs are offered in three sizes that correspond to the outer diameters seen on our line of EVABarrier Draft Tubing. 6.35 mm OD – features a very tight 3 mm ID that requires only 3.2 ft of length for adequate flow resistance. This is the ideal size for mobile draft or if you want to keep your kegerator as tidy as possible. 8 mm OD – the most common OD size of EVABarrier tubing. This size comes in two IDs (4 mm & 5 mm) and pairs up with the lion's share of Duotight fittings and accessories. 4 mm ID is our most recommended size for beverage lines, requiring 5-6 ft. lengths. 5 mm ID is commonly used as gas line or when 10-12 ft. beverage lines are required. 9.5 mm OD – suitable for gas lines or long draw beverage lines. At 6.3 mm ID, this size is ideal for beverage lines that will be 20 ft. or longer in length.
$8.80
