Equipment

This fine mesh filter screen is made of durable, food-grade plastic and perfectly sized to fit the 12" plastic funnel. It will fit snugly into the funnel to prevent the screen from moving and material from flowing around the sides of the screen. The fine No. 35 mesh is perfect for removing pulp or other small particulates, but many brewing applications require a coarser mesh and would easily clog the No. 35 screen. Specifications: Maximum Temperature: 158°F (70°C)  Diameter         5.5″ (13.97 cm) Mesh Size       No. 35  

Read more less

Unfortunately some of us will have to heat our FLEX during the long winter months. No fear, we have the solution! The FLEX heater was carefully engineered to match the heating needs to maintain set temperatures even in the coldest winter garage. It also uses a built in thermostat which stops the heater from getting too warm. This means you get a gentle warming action when your beer drops below your desired temp (opposed to rapid heating which can overshoot or 'cook' your wort). This Spike Brewing heater attaches to their insulated FLEX jacket via Velcro. It is positioned near the bottom cone section of the fermenter where the coldest liquid is. This will give the most even temperature throughout your fermenter (happy yeast!). Specifications: Built in 90F thermostat to prevent the heater from overheating your wort 80 watts of power Durable silicone construction 5' long cord Detailed TC-100 product guide:Product Guide.pdf  

Read more less

All pumps are not equal! The Spike Brewing engineers tested over 15 pumps during the development of this project and found almost all small submersible pumps on the market are grossly overrated. This can greatly affect your temperature control as flow rate is directly proportional to cooling efficiency.   To use: Simply plug our pump into our temp controller Connect your insulated lines to your temp control coil and to the pump outlet Submerse the pump in your cooler (with ice), fridge with cold water reservoir or glycol chiller Start cooling your wort! Specifications: High flow submersible pump 3/8" barbed outlet (connect directly to our insulated tubing) 12v DC powered (much safer than AC submersible pumps) Suction cups to keep pump submerged Detailed TC-100 product guide:Product Guide.pdf

Read more less

This copper counterflow chiller is probably one of the fastest ways to chill wort.  It can be more effectively flushed out after use in comparison to a plate chiller that has small crevasses to trap hop material.   These chillers are 9" in diameter and about 7" high. The input and output are approximately 3/8" outside diameter (10mm). These can be used with gravity, although a pump is recommended.

Read more less

The Hop Spider keeps hops together during the boil, and can be used on all appropriate sized boil pots, including the Grainfather.Made with a coarser, 800 micron mesh, for maximum wort flow and increased hop utilization.Designed with a specifically fitted hook design which can be hooked onto the side of any brew pot or the Grainfather system support ring. Perfect for those of you who would like the reassurance of a hop spider when brewing.This spider can be used for any kind of hops, including hop pellets. Specifications: Diameter: 5.9" Length: 11.8" Material: 800 micron 304 grade stainless steel mesh, with stainless steel support band and single hook.

Read more less

Limited inventory available in store.  Please allow additional time for processing. BrewBuilt's T.C. kettles were designed to keep pace with the ever-evolving world of brewing technology. The appetite for tri-clamp fittings continues to grow in the homebrewing market as T.C. fermenters and pumps become more affordable and widely available. Tri-clamp fittings, also known as Tri-clover, allow you to make a sanitary connection that is free of nooks and crannies for contaminants to take hold. They are much easier to break down for cleaning compared to threaded connections, and they don’t require Teflon tape to make a watertight seal. T.C. fittings and accessories also give you the distinct advantage of being able to clean in place (CIP), so you don’t need to break down your entire system after every brew day. The base model comes without fittings so you can add whatever tri-clamp accessories best suit your needs. Also available with a Ball Valve or Butterfly Valve hardware pack. These days homebrewers have a lot of strong choices when it comes to their kettle purchase. BrewBuilt has adopted a modern feature set designed to make the brew day easier. Silicone handle and lid grips help prevent burns. Etched internal volume markings make filling the kettle for mash or boil simple. Welded valve and thermometer ports are leak-free and never require maintenance--no more discovering worn gaskets on brew day. Sealed handle rivets are strong and allow the entire kettle to be filled if necessary. And perhaps best of all, it features the signature BrewBuilt notched lid with a silicone plug that allows the lid to be in place while using immersion chillers or an Ultimate Sparge Arm. These kettles are truly designed for brewing.Key Features: Two welded T.C. couplers for a lifetime of leak free use AISI304 Stainless Steel construction for longevity and excellent corrosion resistance Stainless handles and rivets for secure lifting Silicone coated kettle and lid handles for heat protection Lid is designed to conveniently hang from a handle 4 mm Tri-Clad Bottom with Aluminum Core heats quickly and disperses heat evenly to prevent scorching Induction burner compatible 1.0mm (10 & 15 gal) or 1.2mm (20, 30 & 50 gal) thick side walls resist denting 1.2:1 height to diameter ratio provides optimal evaporation rate during boiling Industry-First notched lid with silicone plug accommodates an immersion chiller or sparge arm Internally etched volume markers from top to bottom for easy filling BrewBuilt Homebrewing Products: Designed for Brewing, Built to Last. Size Kettle ID (in.) Height (in.) 10 13.78 16.54 15 15.75 18.90 20 17.72 21.26 30 19.69 23.62 50 23.62 28.30 Limited inventory available in store.  Please allow additional time for processing.

Read more less

Built to transform steam into liquid during the boil, Spike Brewing's steam condenser lid will enable you to brew inside without worrying about moisture collecting on your walls and ceiling, which can cause mold issues. These lids are not only designed to fit Spike kettles, but will also work with most other kettle brands on the market. From a better boil-off rate to major cost savings and conveniences, you will find many benefits by adding this to your brew setup. Features & Specs: Compared to boiling without a lid, the Steam Condenser Lid has a 50% reduced boil-off rate and results in a ~6% total boil-off. Replaces the need to install a hood for indoor brewing Prevents mold from forming on walls and ceiling Third-party lab tested to show that DMS is completely undetectable (under 25 ppb) after only 30-45 minutes of boiling Discharge water is very hot and can be used for cleaning Compatible with Spike Kettles and the Spike Solo 1.5" tri-clamp port for CIP ball 4" tri-clamp port for hop additions Water usage: 15 gallons/hour for 10g, 15g & 20g lids 25 gallons/hour for 30g &. 50g lids Lid, pump, condenser mister, piping, clamps, gaskets, barbs & caps included with purchase For more information, see Spike Brewing's FAQ. To get started using the lid, see our Steam Condenser Lid Product and Process guides. Note: Limited inventory availability in-store.  Sizes not carried in-store will be drop shipped from the vendor.

Read more less

10 GALLON STAINLESS BREW KETTLE - V4 Spike Brewing has once again re-designed their brew kettle.  They make one of the best brewing kettles available on the market.  It is the thickest kettle on the market, with US welded fittings (no more weldless fittings) at a factory direct price. Kettle Features: 2.5 - 6 gallon batch size 304 (18/8) stainless steel  Sanitary welded coupler design (done at our facility in Milwaukee, WI) 1.2mm thick walls (thickest on the market) 5mm tri-clad bottom (induction capable) Internal volume markings Polished finish 13.8¨ wide by 17.0¨ tall Domed bottom design Bottom coupler 1.5" off the bottom (1 gallon mark) Top coupler 6" off the bottom (4 gallon mark) Lid is included Pictured Ball Valve and Thermometer Sold Separately. Limited availability in store.  Drop ships from vendor.

Read more less

Designed to be used with the Grainfather G40 or G70, the Whirlpool Arm is a new accessory that makes the whirlpool stage of your brew day even easier. Simply connect it to your G40 or G70 recirculation pipework and let the Whirlpool Arm do the hard work for you by creating a whirlpool without any manual stirring needed. How to use the Whirlpool Arm At the end of the boil ensure that the pump and recirculation valve are both switched off. Connect the Whirlpool Arm to the recirculation pipework so that the other end sits below the surface of the wort. Ensure the wort temperature is below 99°C (210°F) or at your proposed whirlpool temperature, then switch on the pump and slowly open the valve to start recirculating the wort. Add your whirlpool hops and recirculate as per your recipe. When complete, switch the pump off and carefully remove the whirlpool arm using the black silicone handle (caution: the handle may be hot) and then connect your counterflow wort chiller to complete the chilling process according to your G40 or G70 instructions. Material: 304 grade stainless steel Thickness: 1.5mm Length: 365mm

Read more less

The DigiMash is one of the most affordable options in all-grain electric brewing. Includes 35L Gen 2 DigiBoil, false bottom, malt pipe with bottom screen, wire support, and malt pipe handle. This model runs off 110V power and has dual heating elements (1000w and 500w) that can be controlled independently. Includes 304 stainless steel 1/2" ball valve with 13mm barb (approx. 1/2"). DigiBoil Features: 304 stainless steel construction 9 gallon total capacity Digital temperature control 110V / 15A power and plug (5 ft. cord) Stamped-in volume markers (gallons & liters) Temperature reads in °F or °C With elements turned off, hold both +/- buttons to switch between °F or °C Recommended max. grain bill - 18 lbs Recommended min. grain bill - 8 lbs External Dimensions: 29" H x 15" W (including handles) Internal Dimensions: 19.5" H x 11.75" W Mash Upgrade Includes: False bottom Malt pipe Wire support  Malt pipe handle Malt pipe bottom screen

Read more less

For use with an in-line plate filter. These pads will provide between 1-2 Micron filtration.Each filter pad set is good for approximately 5 gallons of beer. These pads are not designed to be back flushed and reused and should be used in one session.

Read more less

BevBright Cartridge Filters are an inexpensive, easy to use, and effective filtration media.  The 3 micron cartridge is the most popular and most recommended filter. It offers a great balance between the high capacity of the 5 micron and the ultra-clear polish of the 1 micron. The dual zone construction helps the 3 micron cartridge remove larger sediment without clogging prematurely and still effectively removes yeast and fine particulates from solution. 98% Super High Efficiency cartridge. Removes 98% of the material 1 micron or larger in a single pass.

Read more less

BevBright Cartridge Filters are an inexpensive, easy to use, and effective filtration media. Use the 1 micron filter as a final, ultra-clear polish only when your product is already very well settled. Excessive yeast or sediment in solution will quickly clog up the 1 micron cartridge. Product that is cloudy in appearance from anything other than a protein haze should be run through a 3 or even 5 micron prior to 1 micron filtering. 98% Super High Efficiency cartridge. Removes 98% of the material 1 micron or larger in a single pass.

Read more less

For those of you who brew in cooler climates, the Graincoat is the perfect product for you.This heat insulation jacket is designed to be used with the Grainfather to keep heat contained in the boiler and maintain a constant temperature during your brew.Material - SBR Foam (0.27" thickness)Easy to wipe clean, polyurethane outer layer and machine washable.

Read more less

Limited supply in-store available for pickup. Due to the weight and dimensions of the Grainfather GC4 Glycol Chiller, this item is shipped palletized freight from the vendor to prevent damage from occurring in transit.  Please allow additional time for processing. Control your fermentation temperature accurately every time!Temperature control is one of the most crucial elements for producing a good quality beer. It needs to be regulated and stable throughout the whole fermentation process to ensure the yeast doesn't get stressed and ferments correctly to get the right flavor profile.  With the ability to individually power and control the temperature of up to four Grainfather Conical Fermenters, each with their own fermenting schedules, the Grainfather Glycol Chiller is the perfect addition to ensure craft brewery-like results.  With the addition of the Glycol Chiller, your system is operating at the ultimate level and you are even able to cold crash and lager. The cooling sleeve is located in between the two stainless steel walls of the Conical Fermenter which is then hooked up to the Glycol Chiller. Temperature is dialed into the digital temperature controller and the liquid travels through this sleeve, cooling the stainless steel which in turn cools the beer in the fermenter. The cooling sleeve never comes into contact with the beer, is completely concealed and does not need cleaning or sanitizing - a true innovation for a fermenter on this scale.  Features: Allows you to cold crash 23 L of wort to as low as 4ºC Allows you to cold crash, lager  control fermentation at low temperatures (as low as 4ºC) Cools and powers up to 4 Conical Fermenters at different temperatures and fermenting schedules.  What's Included: Glycol Chiller Wall outlet power cord with plug 2 x brass couplers (with self-sealing hose connections) 2 x 2 m insulated hoses Specs: LED display 1.5 US Gal glycol tank 300 W 110 – 120 V, 60Hz 390W x 450D x 656H Weight: 62 lb 24 Month  Equipment Warranty Glycol not included. Limited availability in store, drop ships from vendor.

Read more less

Use the StaVin Infusion Tube when you are making wines in neutral barrels and want to gradually integrate a level of oak compounds. With each 8-ounce load of the Infusion Tube, you will be adding only 33% of new oak flavors. The Infusion Tube is a convenient way to add oak incrementally to your neutral barrels without removing barrel heads. Crafted from high quality 304 grade stainless steel, the StaVin Infusion Tube enables the winemaker to control incremental amounts of oak integrated into the wine during fermentation, aging, or prior to bottling. The Tube is also easy to load and remove, which makes it sanitary. It can be removed from the barrel and easily cleaned. The Infusion Tube can be reused indefinitely, making it as ecological as it is economical. The tube accommodates 8 oz of Oak Cubes at a time. 24" L x 1 3/4"D with a 5" stem.

Read more less

Replacement tip for 1/2" auto-siphon

Read more less

Spike Brewing 1.5" TC Ripple Element Specifications: 240 Volt, 5500 Watt Stainless Element Includes 1.5" TC Gasket and Clamp  

Read more less

Spike Brewing's TC100 temp control system will manage both cooling and heating of your Spike Conical. The digital controller's temp probe will feed into the included thermowell on our CF Series Conical. Also included is a specially fitted neoprene jacket which features reinforced port holes to reduce the chance of ripping during install. Last (and maybe the coolest item) is Spike Brewing's special insulated tubing. This almost eliminates tube cooling losses and will prevent your cooling lines from sweating all over your floor! Cooling:When the temp in the conical rises above the set point it will turn on the pump submerged in your cold water reservoir (bucket of ice water, dorm fridge, aquarium or glycol chiller, DIY AC chiller, etc). This will pump cold water/glycol through the temp control coil, which mounts to the lid, cooling your beer until it reaches the controller set point. Heating:When the temp in the conical falls below the controller set point the optional heater will kick on warming the unit up.  Detailed product guide:Product Guide.pdf TC100 Package:-Digital closed loop controller (heating and cooling)-Insulated tubing (more efficient and no more sweaty tubes!-Temp control coil-Neoprene insulated jacket-Submersible pump (pumping cold water through the temp coil)-Temp Coil Quick Connect Fittings TC100 + Heat Package:-TC100 Package (above)-Optional heater (for us northern brewers)    Limited availability in store.  Drop ships from vendor.

Read more less

Replacement mesh liner for a 40L bladder press.  It is similar to a mesh bag but is open on both ends so it can slide over the bladder portion of the press.

Read more less

This heavy-duty pulley is made from strong nylon strapping, laser cut 304 grade stainless steel and is capable of lifting large heavy loads with ease. It's the perfect pulley for lifting the heavy malt pipe from your BrewZilla or other all-in-one system. It's a bit more expensive than other pulley systems, but there's no comparison when it comes to easily lifting or lowering the malt pipe. The included strap is 10m long by 25mm wide (32.8 ft. x 1 in.). The pulley system enables you to multiply your pulling force by 4 times. If you apply 60 lbs of pulling force, the pulley can lift 240 lbs with relative ease. Be sure that the beam you mount the pulley to is rated for the total amount of force being applied i.e. pulling force plus load weight, so for this example 300+ lbs.

Read more less

If you are looking for the easy way to lift your malt pipe from your single vessel BrewZilla or other brewery then this is the easy way to do it. The setup includes all the parts you need. Simply screw the shackle into the roof or overhead beam and then secure the wall cleat and away you go. It will only take a couple moments to install. The double pulley is used so it's possible to lift the large malt pipe in the 65L BrewZilla unit. This stainless steel pulley set has been made from all 304 grade stainless steel, nylon and non-corrosive materials. Suitable for: 35L and 65L BrewZilla or brew in a bag. Contains: 6mm x 8 meters rope 1 x Nylon Wall Cleat 2 x Stainless Pulley 2 x Stainless Carabiner 2 x Stainless Band Rope Anchor

Read more less

These Spike Brewing Spike+ false bottom is for use with their Spike+ line which uses TC fittings. For the standard Spike kettle line that uses NPT fittings please see HERE. Design Features: All stainless design; no Silicone gasket to make a seal Low profile design; extremely low dead space (<.25gal)  Best filtering on the market due to dual stage filter design; 99.9% grain filtering efficiency TC Pickup tube, gasket and clamp are included False bottom and pick up tube are Made in the USA! 2 Stage Filtering: Stage 1: Filters through top plate's optimally engineered sized laser cut slits Stage 2: Bottom ring supports the grain weight while also filtering the wort again before it reaches the pickup tube **False bottoms are not designed to filter pellet hops in the boil kettle. Instead you'll want to create a whirlpool to center the hop material and then drain using a side pickup (HERE)**

Read more less

Flare threads make it quick and easy to disconnect and sanitize your air stone. Made from 316 stainless steel, 1/2" diameter, stone is 1" in length.

Read more less

A compact submersible pump for small cooling projects or building a DYI bucket carboy/keg cleaning system.       Specifications: Maximum flow rate: 1300 GPH Max lift height: 10 ft. Comes with 2 barb fittings - 1/2" & 3/4"  High quality 100W motor runs quiet Stainless steel impeller shaft 6 ft. long power cord For cooling, recommended for batch sizes between 10 gallons to 2 bbl

Read more less

Easily attach to the Grainfather Conical Fermenter, for a clean and simple way to transfer your beer without the need to lift the fermenter to perform a gravity fed transfer. This also ensures less chance of oxygen entering the beer during transfer. All you need is a C02 bottle and a regulator to attach to the Pressure Transfer and you can transfer your beer into a keg or bottles through the Conical Fermenter Dual Valve Tap or via the top of the fermenter lid using the Beer Racking Pipe. NOTE: Batteries are not included for the Pressure Gauge. 2 x AAA batteries are needed. Specifications: High quality 304 stainless steel components Accurate digital pressure gauge Needle valve for precise control of pressure

Read more less

3/8" ID welded stainless steel filter that fits over your stainless steel racking cane or your keg dip tube. Not recommended for plastic racking canes.

Read more less

For use with an in-line plate filter. These pads will provide between .3 - .5 Micron filtration. This pad is the right choice when you want to promote sterility in the bottle, although do please note that the pad does not remove 100% of bacteria - only an absolute rated .45 micron or less cartridge filter can do so. Then why do we sell this pad? Some experienced winemakers who are familiar with their wine and who do not have a cartridge filter use this pad to remove most ml bacteria, making it less likely that an unwanted ML fermentation takes place in the bottle. Each filter pad set is good for approximately 5 gallons of wine when the wine has already been filtered by the polish pads. These pads are disposable.

Read more less

Replacement 4" Burner for Bayou Classic burners.   Model: AL10 4" Burner 9" Length No-Rust Cast Aluminum

Read more less

Replacement O-ring for 10" filter housing unit.  Prop 65 Warning: This product contains a chemical known to the State of California to cause cancer, birth defects and other reproductive harm.

Read more less

The Spike Brewing insulated FLEX jacket uses high quality, extra thick, yet flexible neoprene material to insulate your FLEX from the worst ambient conditions like a hot garage or cold basement. Each custom designed, hand stitched (in the USA) jacket is custom tailored to fit the FLEX. This jacket was designed by a former Lululemon designer because if you're going to cover up shiny stainless steel it better look amazing. We think she did the trick!   Specifications: Sewn in the USA (of imported fabric from Japan and China) Reinforced stitching around all ports, legs and handles for extra strength Helps maintain stable fermentation temps regardless of ambient conditions Stops the tank from ‘sweating’ in warm weather Interior Velcro for attaching the optional heater Machine washable Detailed TC-100 product guide:Product Guide.pdf 

Read more less