Regulators & Repair
KOMOS® Premium Dual Body CO2 Regulator
Send different pressures to two separate kegs from the same CO2 tank with the KOMOS Dual Body Regulator. This industrial gauge regulator aims to be the last regulator you'll ever need. Large dual-body and precision diaphragms provide high flow rates, and pressure settings are quickly and easily dialed in the with hand knobs. The pressure gauges are made from thick stainless steel and come with rubber bumpers for an extra layer of protection. Triple-scale dial faces read in psi, bar, and kPa. Comes with 1/4" flare fitting with barbed outlets. Included Duotight adapters allow the regulator to be easily used with EVABarrier draft tubing. Features: 0–60 PSI operating range Low pressure gauge reads from 0–100 Pull ring PRV rated to blow off at 65 PSI Strong, robust design Highly accurate precision diaphragm Easily adjusted by hand 1/4" flare fitting with barbed outlet Duotight adapter fitting included for use with EVABarrier draft tubing Heavy duty steel gauges with rubber bumpers M6 mounting screw holes Made in accordance with AS 4267 Made in China Warning: This product contains lead and/or lead compounds, a chemical known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warning.ca.gov
$110.00
Handheld Co2 Keg Charger
Portable CO2 charger that eliminates the need for costly CO2 tanks & hoses. Pressurizes any 3 or 5-Gal corny keg. Works on either ball-lock or pin-lock fittings with 1/4" flare connection. Cartridges and connectors are not included.
$24.99
Gas Manifold Nipple
1/4" brass nipple for expanding a modular gas manifold. Right hand thread.
$5.50
Premium Plus Secondary Regulator - Pass-thru
Safely and effectively control the flow of CO2 to a single keg in your draft beer system. Secondary gas regulators reduce pressure from a primary regulator or gas blender and provide this lower pressure to each individual keg. Easily add another carbonated beverage to your existing system with this Premium Plus secondary regulator; the integrated pass-thru bar saves time and provides convenience in the field. For added safety, the integrated pressure relief valve stops the gas flow if the pressure gets too high (55-65 PSI). Premium Plus regulators come standard with a tamper-evident adjustment screw and bonnet, preventing unauthorized adjustment to gas pressure which can cause service issues. FEATURES Adjust pressure from 0 to 60 PSI Built for durability: forged brass body, accurate machining, chrome-plated finish Premium quality metal gauges for durability Tamper-evident adjustment screw and bonnet Enlarged CO2 port for high volume Factory leak tested at 145 PSI Safety relief valve releases at 55-65 PSI Made in the USA Specifications: Performance: 1 Pressure / 1 Product Height: 7-1/4" Width: 3-3/4" Depth: 5-1/2" Output Pressure Gauge: 0-60 PSI, for accurate product pressure Outlet Barbs: 3/8" O.D. (To fit 5/16" I.D. Gas Hoses) Pressure Relief Valve: Safety Pressure Relief Valve Releases at 55-65 PSI Capacity: Safety pressure relief valve releases at 55-65 PSI
$69.99
Gas Shut Off Valve
This shut-off valve is for draft beer gas regulators & gas distributors. Specifications: Right Hand 1/4" NPT (National Pipe Threads) 3/8" O.D. (To fit 5/16" I.D. Gas Hose) Does not include a check valve.
$14.99
CO2 Inlet Nipple, LH
CO2 inlet nipple with o-ring tank seal, left hand threads
$9.99
Inlet Fitting Nut
Replacement chrome plated nut for Co2 Inlet stem. CGA-320 thread (Intended for use with a CO2 Regulator)
$7.99
Duotight Mini Gauge 0-15 psi
This mini pressure gauge is compatible with the BlowTie 2 spunding valve, Duotight in-line regulator, and KegLand mini regulator. It is recommend using the gauge with a range closest to your desired pressure setting. Pressure Range: 0-15 psi (0-1 bar) Body Dimensions: 26mm x 26mm x 15mm Probe Diameter: 8mm
$7.70
Co2 Gas Regulator Y Fitting, Chrome Plated Brass
Co2 gas regulator wye fitting for adding an additional shutoff. Specifications Material: Brass Finish: Chrome Plated Brass Thread Size: 1/4MPT x 1/4 FPT x 1/4 FPT Warnings / Instructions Important information: Prop. 65 for CA residents.Proposition 65 Warning: This product contains chemicals known to the State of California to cause cancer and/or birth defects or other reproductive harm.
$7.99
Krome Primary Precision Plus CO2 Regulator with 1 Outlet
Krome dispense is dedicated to manufacturing the highest quality gas equipment in the industry. Our new Single outlet CO2 regulator has some industry features, making it a better performing, higher-quality, and more-tested regulator. Take Advantage of our Premium Plus low pressure primary regulator to securely regulate the flow of CO2. In addition, this model has a built-in pressure relief valve that releases pressure if it goes above 55 to 65 PSI. Our Precision Plus Co2 Regulator comes with an output gauge that monitors pressure up to 60 PSI. Krome’s Precision Plus beer gas Regulator give you options for various beers, and the tank gauge has a range of 0–4500 PSI. Gauge can help you to aware of the amount of pressure left in your cylinder. The brass body of the regulator makes it safe and leak proof. These regulators provide maximum convenience and durability to bars and restaurants. Suitable for all industrial applications. The main CO2 gas regulator’s purpose is to lower the high pressure in the gas cylinder to a lower, practical pressure for dispensing. Feature: Made of high quality machined brass and can use with a variety of gases. Adjust pressure from 0 to 60 PSI metal gauges of better quality and durability It made to dispense cold brew, wine, and beer. High output flow rates with constant pressure supply Modification-proof adjustment screw and bonnet. CO2 CGA320 connection expanded for high volume Installation is easy . The Safety relief valve releases at 55-65 PSI The needs of the most active pubs and restaurants are satisfied by commercial grade design. For dispensing beer gas regulator, wine and cold brew, or servicing a gas blender These are utilized on a range of gases, including nitrogen, helium, argon, oxygen, and CO2. Suitable for Medium to Large Dispensing Systems.
$60.00
KOMOS® Standard Kegerator - Replacement Gas Cylinder Bracket
Co2 cylinder bracket that accommodates 5 pound and 10 pound tanks. This is the bracket that is included with the KOMOS® Standard Kegerator. Having an additional bracket is a great way to mount a Co2 tank near your fermenters for pressurized transfers.
$16.50
74 gram CO2 Cylinder (Torpedo Compatible)
One canister will push between 1-4 five gallon Cornelius style homebrew kegs, depending on how it is used and the CO2 consumption required. Please Note: This unit is compatible with the Torpedo Mini CO2 Regulator 5/8-18 threading 74 g cartridge Shipping Restricted: This product is only eligible for ground shipment within the contiguous 48 states. C02 Warning: Warning, this product is a gas that is under pressure. Please make sure that when in use the bottle remains in an upright position. Please use extreme caution when using.
$18.00
Add-On Premium Plus CO2 Regulator
Micro Matic is committed to producing the best quality gas equipment in the industry. Made right here in the USA, every regulator that leaves Micro Matic's plant goes through a rigorous quality control testing process ensuring accuracy, reliability and optimal performance in the market. Their new Premium Plus regulator offers industry leading features, providing a better performing, better quality and better tested regulator. Easily convert any primary CO2 regulator into a dual product primary regulator. Premium Plus Add-On CO2 regulator is ideal for dispensing two draft beers that require different CO2 pressures. The add-on module type design makes expansion easy. Features: Built for durability: forged brass body, accurate machining, chrome plated finish Premium quality metal gauges for durability Factory leak tested at 2900 PSI Tamper evident adjustment screw and bonnet One piece heavy duty seat capsule Durable built in long lasting solid nylon inlet seal Enlarged CO2 port for high volume Constant pressure supply at high output flow rates Adjust pressure from 0 to 60 PSI Safety relief valve releases at 55–65 PSI Made in USA For home or commercial use Specifications: Performance: 1 Pressure / 1 Product Output Pressure Gauge: 0-60 PSI, for accurate product pressure Outlet Barb: 3/8" O.D. (To fit 5/16" I.D. Gas Hoses) Pressure Relief Valve: Safety Pressure Relief Valve Releases at 55-65 PSI Capacity: SCFM 3.5 Max Installation: CO2 tank mount (CGA-320 threads) WARNING:This regulator must be connected to a primary CO2 regulator. The threaded high pressure port on the left hand side is designed for a tank mount (primary) regulator. Not connecting a regulator to this exposed port will allow high pressure CO2 to vent straight through the regulator body. Batteries with more then two regulators should be wall mounted. This is done with the addition of wall brackets for mounting and a high pressure CO2 hose for connection to the gas cylinder. To prevent your gas cylinder from falling over and damaging the regulators, be sure the cylinder is always secured in an upright position with either a chain or strap. Additionally, be sure the cylinder is located away from any sources of heat.
$89.99
BlowTie 2 Diaphragm Spunding Valve with Gauge
The Blow Tie Spunding Valve is used to release excess pressure on a pressurized fermenter or from a keg while doing pressure transfers. Thanks to the large surface area of the diaphragm, this style of spunding valve is much more accurate than the poppet style. The 8 mm Duotight fittings at both inlet and outlet make this unit perfect for use with EVABarrier 8 mm OD tubing. The BlowTie 2 features an integrated pressure gauge so you can quickly and easily dial in your pressure setting. The gauge is removable and can be swapped out with a gauge of a different pressure range. Specifications: Made from food grade acetal Stainless screws Easily disassembles for cleaning 8mm (5/16") Duotight fittings at both ends Interchangeable pressure gauge Gauge reads from 0-15 psi WARNING: Do not exceed gauge pressure. Exceeding the pressure range will damage the gauge.
$22.00
Regulator Inlet Flare Fitting, LH
Regulator inlet flare fitting for primary regulators. 1/4" NPT (left hand) x 1/4" flare Does not include check valve
$2.75
Regulator Gauge Cage
Made from 304 stainless steel, set of 2, for the front and back of your gauges. These cages will protect your regulator gauges from damage. Works with Micro Matic and NADS regulator.
$19.00
4-Way Gas Manifold with Pressure Relief
This manifold allows you to serve four beers at the same pressure. It’s made from brass and features a pressure relief valve, shut offs with check valves, 3/8” inlet and outlet barbs, and a 304 stainless mounting bracket.
$44.99
Regulator Inlet Flare Fitting, RH
Regulator inlet flare fitting for primary regulators. 1/4" NPT (Right Hand Thread) x 1/4" flare Does not include check valve
$2.99
74g Cartridge Adapter for KegLand Core 360 Mini CO2 Regulator
This adapter can be installed on the Core 360 Mini Regulator from Kegland in order to use 74 gram CO2 cartridges. Use a crescent wrench to remove the stock adapter piece for 12 gram cartridges and simply screw in this adapter with 5/8-18 UNF female threading. Switching to 74 g cartridges will allow you dispense 1-4 Cornelius kegs, depending on how it is used and the CO2 consumption required. TR21-4 Male Thread x 5/8-18 UNF Female Thread Adapter only. Regulator and CO2 cartrdige sold separately. KegLand Part Number: KL20411
$5.50
KOMOS Gauge Cage
Stainless steel gauge cage for KOMOS CO2 dual gauge regulators. Includes mounting screws. Pictured regulator not included.
$22.00
Hex Nipple, LH
Hex nipple, 1/4" NPT, 9/16" hex, 1.87" overall length, for primary regulators, left hand threads
$9.99 $7.99
Brass Air WYE, 1/4NPT, (2) 1/4NPT
"Y" fitting body, 1/4"NPT (male) x (2) 1/4"NPT (female), no outlet fittings
$12.99
Taprite Regulator Gauge Protector
Protect your Taprite brand regulator with this metal guard. Tanks occasionally tip over and damage the gauges when they do. This guard takes the blow instead of your gauge. Attaches to the regulator by screwing into the back. Does not work with the Micromatic or Komos branded regulators.
$19.99 $12.99
Pressure Gauge, 0-160 PSI
Pressure gauge, 0-160 psi, 1/4" npt bottom inlet, right hand threads.
$9.95
Brass Hex Nipple, LHT
Left hand thread (LHT), brass hex nipple generally used for regulator and manifolds. Specifications: 1/4" NPT x 1/4" NPT (LHT) 9/16" hex 1-3/8" length
$4.99
Duotight In-Line Regulator | Built-In Pressure Gauge | 0-150 PSI | Liquid & Gas Compatible | 6.35 mm Duotight
The Duotight In-Line Regulator works with both gas and liquid. Easily adjust the flow can be adjusted with the yellow adjustment knob. 6.35 mm Duotight fittings at both inlet and outlet make this unit perfect for use with 6.35 mm OD tubing. Features an integrated pressure gauge so you can quickly and easily dial in your pressure setting. The analog gauge is removable and can be swapped out with a gauge of a different pressure range or it can be swapped out for the Digital Mini Pressure Gauge. The size of the Duotight connection and the extended 0-150 PSI pressure range makes this model perfect for stepping down the pressure of your mains water line for use with water filtration or RO systems. Specifications: Made from food grade acetal Stainless screws Easily disassembles for cleaning 6.35mm (1/4") Duotight fittings at both ends Interchangeable pressure gauge Gauge reads from 0-150 psi Made with quality EPDM seals Wall mountable WARNING: Do not exceed gauge pressure. Exceeding the pressure range will damage the gauge.
$19.50
Beer Nitrogen Regulator to CO2 Tank Adapter
Draft Beer CO2 regulator to nitrogen tank adapter Quickly converts a Nitrogen into a CO2. If you own a nitrogen regulator and want to use it on a Co2 tank, then the following adapter can save you money! Simply screw on one side of the adapter to your nitrogen regulator and the other side to your Co2 tank valve. Connects a nitrogen regulator to CGA-320 Co2 tank valve
$15.99
Premium Plus Secondary Regulator 0-15psi
This Premium Plus low pressure primary regulator has a 15 PSI gauge head for accurate adjustment in low pressure dispensing applications. Many wine and cask conditioned systems use 5 PSI or lower for dispensing and maintaining a low pressure blanket on the wine or beer. For added safety, this model has an integrated pressure relief valve that stops the gas flow if the pressure gets too high (55-65 PSI). Premium Plus regulators come standard with a tamper-evident adjustment screw and bonnet, preventing unauthorized adjustment to gas pressure which can cause service issues. FEATURES Adjust pressure from 0 to 15 PSI Built for durability: forged brass body, accurate machining, chrome-plated finish Premium quality metal gauges for durability Tamper-evident adjustment screw and bonnet Nickel-plated valve seats for high corrosion resistance Enlarged CO2 port for high volume Safety relief valve releases at 55-65 PSI Factory leak tested at 145 PSI Made in the USA Excellent for dispensing keg wine and cask beer Specifications: Performance: 1 Pressure / 1 Product Height: 7-1/4" Width: 3-3/4" Depth: 5-1/2" Pass-thru barbs, Includes plug
$69.99
CO2 Gas Cylinder Holder
Adjustable chain to fit cylinder diameter. Holder for Cylinder 1 Can hold the cylinder maximum of 166mm Diameter
$7.99
Regulator Outlet fitting - 3/8" barb
Threaded Nipple with 3/8" O.D. Hose Barb (Right Hand Thread) Right Hand 1/4" NPT to 3/8" barb
$5.99
Regulator Outlet fitting - 1/4" barb
Threaded Nipple with 1/4" O.D. Hose Barb (Right Hand Thread) Right Hand 1/4" NPT to 1/4" barb
$2.99
Fiber Co2 Inlet Washer - 10 pack
Economical fiber washer for CO2 regulator. Fits between the gas cylinder and regulator connection. 10 Pack
$7.50
CO2 Regulator Inlet Nipple - LHT
Replacement keg beer regulator CO2 Inlet Nipple. Specifications: 1/4" NPT Left Hand Thread (LHT) 2-1/4" Length
$14.99
6-Way Modular Gas Manifold
This modular gas manifold will allow you split one CO2 line to six of them. Each line can be turned off individually without affecting the flow to other kegs. Each ball valve contains a check valve that ensures no beer or gas can flow between the two kegs. The barbs are all 5/16" which is standard for gas line in the beer industry. If later, you decide to add an additional keg this manifold can be expanded using the Add On Assembly.
$77.00
Mini Regulator Adapter
Allows you to easily use a 74g CO2 cartridge with your 16g hand held keg charger. This adapter has a 5/8" male end and a 3/8" female end.
$9.95
5lb Co2 Aluminum Cylinder - Empty
5 pound aluminum CO2 cylinder. Ships empty. Will dispense approximately 9 five gallon kegs before needing to be refilled. Dimensions: 18" Tall x 5.25" wide.
$88.00
