Kegs & Parts

Nothing is more refreshing that having your own soda water on tap at home.  SodaStream units are great but filling up those tiny 1L bottles is a pain and those small CO2 cylinders run out fast and are expensive to swap.  Solve this problem once and for all with the Continuous Soda Carbonator Keg Reactor Solution. KegLand has invented this really easy-to-use keg lid that attaches to a standard ball lock keg.   Setup: Position the keg inside your fridge or kegerator (ideally below 40°F). Attach your beverage draft line to the soda water out post. Attach your gas line to the gas-in post. Set your CO2 regulator to 30-50 psi, depending on how highly carbonated you like your soda water. We highly recommend using a check valve on your CO2 line. On first use, purge the air from the headspace of the keg. Connect the mains water to the water inlet post on the lid of the keg. It is recommend to also use a check valve on your mains water line to prevent soda water from going back into your house mains. Depending on your mains water pressure, you may need to reduce it using the Duotight In-Line Regulator. For the Carbonator Keg Lid to work well, the mains water pressure should be 30-40 psi higher than your regulator set pressure (from Step 4). That's it. This simple unit will give you continuous soda water connected to your mains water.

Read more less

The most common relief valve. Fits most Cornelius and Firestone style kegs. Long body with spring with gray top and pull ring. Max. pressure rating: 100 psi

Read more less

Curved beverage (liquid) out curved dip tube for 5 gallon Cornelius style ball lock kegs. Stainless Steel.  

Read more less

When using the Torpedo Buoy™ floating dip tube, you can draw the clearest beer possible from the first pint to the last. Included is a 3" metal dip tube, 23.5" length of 1/4" ID silicone tubing, and stainless steel ball float. This floating dip tube is compatible with any ball lock or pin lock homebrew keg. Sized for 5-gallon kegs, but it can be shortened for use with 1.5 or 2.5-gallon kegs. Instructions

Read more less

Sankey D and S System Spear removing / Opening Demounting Tool​ Stainless steel commercial keg opening tool. Suitable only for D and S system kegs also called American and European Sankey kegs respectively. Use this Keg spear demounting tool​ for cleaning and servicing. Spanner tool to remove the spear from a D-TYPE or S-TYPE keg Sturdy tool with a long rod for easy handling Always degas before proceeding to remove keg valve.

Read more less

These keg filler stickers are designed to help you quickly check the fill volume, especially when filling cold beverages like cold-crashed beer. When the liquid inside is cold, the color changes from yellow to green. For 5-gallon kegs, you will need to apply 2 stickers if you want the gauge to run the full length of your keg. Size: 8.85" x 0.47" Color Warm: Yellow Color Cold: Green

Read more less

Weighted cap design keeps the dip tube submerged, maximizing liquid draw and minimizing air intake for consistent performance Prevents hop material and other sediment from clogging your dip tube, ensuring cleaner beer transfers and samples Works seamlessly with Torpedo Keg Buoys, Kegmenter Floating Dip Tubes, and FermZilla Pressure Kits for diverse brewing setups Made with food-grade HDPE and 304 stainless steel, allowing for easy cleaning and sanitization with common brewing cleaners This handy little filter attachment can be used with the Torpedo Keg Buoy, Kegmenter Floating Dip Tube, or FermZilla Pressure Kit to keep hop material from being sucked into the silicone dip tube. This upgrade accessory is especially helpful if you like to dry hop directly in your keg while serving, or if you want to pull clean samples from your FermZilla or Kegmenter during fermentation when there's still a lot of biomatter in solution. Simply remove the metal tube from the ball float, slip the silicone tubing over the barb, then reattach the ball float to one of three clip locations. Made from HDPE and 304 stainless steel, the filter can be boiled or sanitized with the full range of cleaners that we sell. The plastic HDPE is over molded onto the stainless mesh to make a seamless finish. The end cap can easily pop off for cleaning. This updated version of the original Filter Attachment now includes a weighted cap that helps keep the end of the dip tube pointed down and submerged below the liquid surface level.  

Read more less

Replacement pressure relief valve rated to blow at 35 psi. This is a direct replacement of the PRV featured on the FermZilla and Kegmenter. It is also compatible with homebrew kegs and the KOMOS® CO2 regulator if you desire a lower blowoff pressure.

Read more less

Replacement Beverage Dip Tube for the standard Torpedo Kegs.

Read more less

Replacement pressure relief valve rated to blow at 17 psi. Fits FermZilla and Kegmenter. It is also compatible with homebrew kegs and the KOMOS® CO2 regulator if you desire a lower blowoff pressure.

Read more less

Replacement pressure relief valve rated to blow at 65 psi. This is a direct replacement of the PRV featured on the KOMOS® CO2 regulator. The Green PRV can also be used with pressurizable FermZilla models for hydro testing. Note that under normal operation, the FermZilla should always be used with the Red PRV (35psi).

Read more less

Replacement Beverage Dip Tube for the slimline Torpedo Kegs.

Read more less

Keg spear body o-ring for Sankey D and Sankey S type spears.   Sanke D Spear Exploded View

Read more less

Short dip tube for gas-in side of Torpedo kegs. 1" in length.

Read more less

Fits John Wood and old style Firestone ball lock tanks. Thread size 3/4 - 18, plastic insert included.

Read more less

Locking disc for Sankey D type keg spears.   Sankey D Spear Exploded View

Read more less

- Tank Plug, Ball-Lock (gas)- For Firestone V & VI Challenger and Super Challenger Tanks- 9/16 - 18 Thread size- Plug includes Poppet and O-Ring.

Read more less

Helps protect your keg from scratches from your lid.

Read more less